1EFF : ALL 1 52-13-22Page 402 1 1 May 01/05 1 1 1CES 1
3. Job Set-up
__________
Subtask 52-13-22-010-058
R A. Get Access
WARNING : DO NOT OPEN THE PASSENGER/CREW DOOR IF THE WIND SPEED IS MORE
_______
THAN 65 KNOTS.
WARNING : BEFORE YOU START WORK ON THE DOOR, MAKE SURE THAT:
_______
-
THE EMERGENCY CONTROL HANDLE IS IN THE DISARMED POSITION WITH THE SAFETY PIN INSTALLED.
-
THE PERCUSSION LEVER OF THE DOOR-DAMPER AND EMERGENCY-OPERATION CYLINDER IS IN THE DISARMED POSITION WITH THE SAFETY PIN INSTALLED.
WARNING : STOP THE OPENING PROCEDURE IF THE RED WARNING LIGHT FLASHES.
_______ RESIDUAL PRESSURE COULD CAUSE THE DOOR TO OPEN WITH A SUDDEN FORCE AND INJURE PERSONS AND/OR DAMAGE THE AIRCRAFT.
(1)
Put the access platform in position in front of the passenger/crew door 832 or 842.
(2)
Open the applicable passenger/crew door (Ref. TASK 52-10-00-010-001).
(3)
Obey the special precautions before you start work on the door (Ref. TASK 52-10-00-860-001).
Subtask 52-13-22-865-050
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU EIS/SLIDES/ARM AND WARN/FLT 15WN P11 121VU EIS/SLIDES/ARM AND WARN/GND 13WN P10 121VU EIS/SDAC1 AND 2/DOOR/DET/PAX 48WV P05
1EFF : ALL 1 52-13-22Page 403 1 1 May 01/04 1 1 1CES 1 **ON A/C 001-002,
Subtask 52-13-22-010-059
C. Removal of Components
(1)
Remove the escape slide (Ref. TASK 25-62-44-000-002).
(2)
Remove the door lining (Ref. TASK 25-23-46-000-002) 832FZ, 832GZ, 832EZ, 832DZ, 832CZ, 832BZ, 832AZ.
(3) Remove the door insulation. R **ON A/C 003-049, 051-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 52-13-22-010-059-A
C. Removal of Components
(1)
Remove the escape slide/raft (Ref. TASK 25-62-44-000-002).
(2)
Remove the door lining (Ref. TASK 25-23-46-000-002) 832FZ, 832GZ, 832EZ, 832DZ, 832CZ, 832BZ, 832AZ.
(3) Remove the door insulation.
**ON A/C ALL
4. Procedure
_________
Subtask 52-13-22-020-051
A. Removal of the Emergency Control Handle
**ON A/C 001-002, 051-052,
(Ref. Fig. 401/TASK 52-13-22-991-001)
**ON A/C ALL
Post SB 52-1097 For A/C 001-002,051-052,
(Ref. Fig. 401A/TASK 52-13-22-991-001-A)
1EFF : ALL 1 52-13-22Page 404 1 1 Aug 01/05 1 1 1CES 1
Control Handle of the Emergency Escape Slide
Figure 401/TASK 52-13-22-991-001
R 1EFF : 001-002, 051-052, 1 52-13-22Page 405 1 1 May 01/05 1 1 1CES 1
Control Handle of the Emergency Escape Slide Figure 401A/TASK 52-13-22-991-001-A
R 1EFF : 1 1 1CES ALL 1 111 52-13-22 Page 406 Nov 01/99
**ON A/C ALL
(1)
Remove the cotter pin (3) and discard it. Remove the nut (4), the washer (5) and the taper pin (2).
(2)
Remove the lever (1).
(3)
Remove the cotter pin (28), the nut (29), the washer (30), the bolt
(37) and the washer (35).
(4)
Remove the rod (32), the spring (33), the bushing (34) and the washers (39).
(5)
Remove the cotter pin (25) and discard it. Remove the nut (26), the washer (27), the bolt (38) and the washer (36) and disconnect the rod (9).
(6)
Remove the cotter pin (15) and discard it. Remove the nut (14), the washer (13), the bolt (11), the washer (12) and disconnect the rod (10).
(7)
Remove the cotter pin (16) and discard it. Remove the nut (17), the washer (18) and the taper pin (20).
(8)
Remove the emergency control handle (21) and the washer (22).
(9)
Remove the cotter pin (7) and discard it. Remove the nut (8), the washer (6) and the taper pin (31).
(10) Remove the emergency control handle axle (19), the washer (22), the spacer (23), the bellcrank (24).
Subtask 52-13-22-020-052
B. Removal of the Escape Slide Gearbox
(Ref. Fig. 402/TASK 52-13-22-991-002)
(1) Removal of the plate assembly
(Ref. Fig. 403/TASK 52-13-22-991-012)
(a)
Remove the screw (70), the washer (71) and the closing plate (72).
(b)
Remove the old sealant with a non-metallic scraper and clean the surface with CLEANING AGENTS (Material No. 11-003)
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門2(141)
