(19)
 Install the washer (36), the bolt (38) and connect the rod (9).

 (20)
 Install the washer (27) and the nut (26).

 (21)
 TORQUE the nut (26) to between 0.3 and 0.35 m.daN (26.54 and 30.97 lbf.in).

 NOTE : If you install a new bolt (38), drill a hole of 1.9 mm (0.0748
____
 in.).

 (22) Install the new cotter pin (25).
 (23) Remove the RIGGING PIN (98DNSA20206120). Subtask 52-13-22-420-055
 G. Installation of the Escape Slide Control Mechanism
 (Ref. Fig. 408/TASK 52-13-22-991-014)

 (1)
 Put the hook (198) and the spacer (184) in position.

 (2)
 Apply a coat of COMMON GREASE (Material No. 04-004) on the bolt (181).

 (3)
 Install the washers (183), (182), (197) and the nut (196) and tighten it.

 NOTE : If you install a new bolt (181) drill a hole of 2.8 mm (0.1102
____
 in.).

 (4) Install a new cotter pin (195).
R 1EFF : ALL 1 52-13-22Page 438 1 1 May 01/00 1 1 1CES 1

 (5) Put the rod (180) in position and adjust it as follow: R **ON A/C 001-002, 051-052,
 (Ref. Fig. 411/TASK 52-13-22-991-017) **ON A/C ALL R Post SB 52-1097 For A/C 001-002,051-052, (Ref. Fig. 411A/TASK 52-13-22-991-017-A) **ON A/C ALL
 (a)
 Put the emergency control handle in the DISARMED position.

 (b)
 Install the washers (186), (192), the bolt (185) and the nut (194).

 (c)
 Adjust the length of the rod (180) to get the clearance J1 of 2 +0 +0.5 mm (0.0787 +0.0000 +0.0196 in.) between the hook (198) and the emergency control handle.

 (d)
 TORQUE the nut (194) to between 0.3 and 0.35 m.daN (26.54 and

 30.97 lbf.in).
 NOTE : If you install a new bolt (185), drill a hole of 1.9 mm

____
 (0.0748 in.).

 (6)
 Install a new cotter pin (193).

 (7)
 Install the bushing (201) and the spring (200).

 (8)
 Apply a coat of COMMON GREASE (Material No. 04-004) on the axle of the rod end (199) and install it.

 (9)
 Put the end rod (199) in position.

 (10)
 Install the washers (188), (189), the bolt (187) and the nut (191).

 (11)
 TORQUE the nut (191) to between 0.3 and 0.35 m.daN (26.54 and 30.97 lbf.in).

 NOTE : If you install a new bolt (187), drill a hole of 1.9 mm
____
 (0.0748 in.).

 1EFF : ALL 1 52-13-22Page 439 1 1 May 01/05 1 1 1CES 1

 Escape Slide Control Mechanism - Adjustment
 Figure 411/TASK 52-13-22-991-017

R 1EFF : 001-002, 051-052, 1 52-13-22Page 440 1 1 May 01/05 1 1 1CES 1

 Escape Slide Control Mechanism - Adjustment Figure 411A/TASK 52-13-22-991-017-A
 1EFF : 1 1R 1CES  ALL  1 11 1 52-13-22 Page 441 May 01/00

 (12) Install a new cotter pin (190).
 ________

5. Close-up
 Subtask 52-13-22-820-053
 A. Adjustment
 (1)
 Check the adjustment of the escape slide release mechanism (Ref. TASK 52-13-22-820-001).

 (2)
 Do an adjustment of the percussion bellcranck finger of the door damper and emergency operation cylinder (Ref. TASK 52-13-14-820-002).

 (3)
 Check the adjustement of the proximity switch 7WN1 or 7WN2 (Ref. TASK 52-71-00-820-002).

 Subtask 52-13-22-640-050
 B. Lubrication
 (1)
 Lubricate the ends of the girt bar with COMMON GREASE (Material No. 04-004).

 (2)
 Lubricate the mating surfaces of the girt bar and the girt bar fittings with COMMON GREASE (Material No. 04-017).

 Subtask 52-13-22-916-050
 C. Protective Treatment
 (1)
 Apply STRUCTURE PAINTS (Material No. 16-001) to the ends of the screw threads and heads.

 (2)
 Apply another coat of STRUCTURE PAINTS (Material No. 16-002).

 (3)
 Apply SPECIAL MATERIALS (Material No. 05-002) to the screws of the mechanism.

 (4)
 Apply STORAGE PRESERVATION (Material No. 15-007) to the metal parts which are not painted.

 (5)
 Apply a coat of SPECIAL MATERIALS (Material No. 05-027) to all the parts installed.

 1EFF : ALL 1 52-13-22Page 442 1 1 May 01/00R 1 1 1CES 1

 **ON A/C 001-002,
 Subtask 52-13-22-010-060
 D. Installation of Components
 (1)
 Install the door insulation.

 (2)
 Install the door lining. (Ref. TASK 25-23-46-400-002) 832FZ, 832GZ, 832EZ, 832DZ, 832CZ, 832BZ, 832AZ.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門2(148)