1EFF : ALL 1 52-13-18Page 406 1 1 Nov 01/98 1 1 1CES 1

 (3)
 Install the retainer (18), the screws (22), and the nuts (2) and
 tighten them with your hand.

 (4)
 Install the retainer (19), the screws (22), and the nuts (2) and
 tighten them with your hand.

 (5)
 Install the retainer (1), the screws (21), (22), and the nuts (2) and tighten them with your hand.

 (6)
 Install the retainer (3), the screws (21), and the nuts (2) and
 tighten them with your hand.

 (7)
 Install the retainer (16), the screws (21), and the nuts (2) and
 tighten them with your hand.

 (8)
 Install the retainer (15), the screws (21), and the nuts (2) and
 tighten them with your hand.

 (9)
 Install the retainer (14), the screws (21), and the nuts (2) and
 tighten them with your hand.

 (10)
 Install the retainer (4), the screws (21), and the nuts (2) and tighten them with your hand.

 (11)
 Install the retainer (5), the screws (21), and the nuts (2) and tighten them with your hand.

 (12)
 Install the retainer (6), the screws (21), and the nuts (2) and tighten them with your hand.

 (13)
 Install the retainer (7), the screws (21), and the nuts (2) and tighten them with your hand.

 (14)
 Install the retainer (13), the screws (21), and the nuts (2) and tighten them with your hand.

 (15)
 Install the retainer (12), the screws (21), and the nuts (2) and tighten them with your hand.

 (16)
 Install the retainer (11), the screws (21), and the nuts (2) and tighten them with your hand.

 (17)
 Install the retainer (10), the screws (21), and the nuts (2) and tighten them with your hand.

 (18)
 Install the retainer (9), the screws (21), and the nuts (2) and tighten them with your hand.

 1EFF : ALL 1 52-13-18Page 407 1 1 Nov 01/98R 1 1 1CES 1

 (19)
 Install the retainer (8), the screws (21), and the nuts (2) and tighten them with your hand.

 (20)
 Make sure that the clearances between the retainers are 2 +1 -1 mm (0.0787 +0.0393 -0.0393 in.).

R (21) Tighten all the nuts (2) to between 0.17 and 0.20 m.daN (15.04 and R 17.69 lbf.in).
 Subtask 52-13-18-220-050
 B. Check of the Clearance
 (Ref. Fig. 402/TASK 52-13-18-991-006)

 (1)
 Check of the seal compression

 (a)
 Close the door.

 (b)
 Make sure that the door seal is correctly compressed on all its length and that the seal compression clearance J1 is 4.5 +2 -2 mm (0.1771 +0.0787 -0.0787 in.).

 (c)
 Open the door.

 (2)
 Check of the screw/nut installation

 (a) Make sure that the screw (22) is flush with the nut (2). The out-of-flush tolerance J2 is: - for the round section seals: 0 +0 -0.5 mm (0.0000 +0.0000 -
0.0196 in.) - for the square section seals: 0 +0 -1 mm (0.0000 +0.0000 -0.0393 in.).
 5. Close-up
________
 Subtask 52-13-18-410-055

 A. Close Access
 (1)
 Remove the ground support and maintenance equipment, the special and standard tools and all other items.

 (2)
 Obey the special precautions after the work on the door (Ref. TASK 52-10-00-860-002).

 (3)
 Close the passenger/crew door 832, 842 (Ref. TASK 52-10-00-410-001).

 1EFF : ALL 1 52-13-18Page 408 1 1 Aug 01/00 1 1 1CES 1

R R  Door Seal - Clearances Figure 402/TASK 52-13-18-991-006
 1EFF : 1 1 1CES  ALL  1 111 52-13-18 Page 409 Nov 01/98

 (4) Remove the access platform(s).

 1EFF : ALL 1 52-13-18Page 410 1 1 Nov 01/98 1 1 1CES 1 SEAL - DOOR - REPAIRS

_____________________
 TASK 52-13-18-300-001
 Repair of the Seal of the Aft Passenger/Crew Door
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific clamp
 No specific fine emery paper
 No specific lint-free cloth
 No specific spatula
 No specific very fine emery paper
 No specific Wooden Bonding Block
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門2(108)