(b)
Install the bush (88), the bolt (89), the washer (86) and the nut (84).
(c)
TORQUE the nut (84) to between 0.6 and 0.7 m.daN (53.09 and 61.94 lbf.in).
(d)
Install a new cotter pin (85). NOTE : If you install a new bolt (89), drill a hole of 2 mm
____ (0.0787 in.) for the cotter pin installation.
(19) Connect the rod (80).
(a)
Put the rod (80) in position in its fitting.
(b)
Install the bushes (79) and (81), the washer (82) and the bolt (83).
(c)
Install the washer (78) and the nut (77).
(d)
TORQUE the nut (77) to between 0.3 and 0.35 m.daN (26.54 and
30.97 lbf.in).
(e)
Install a new cotter pin (76). NOTE : If you install a new bolt (83), drill a hole of 1.9 mm
____ (0.0748 in.) for the cotter pin installation.
(20)
Install PIN - RIGGING (98D52103006000) on the bellcrank assembly (125).
(21)
Connect the rod (92) as follows: (Ref. Fig. 408/TASK 52-11-21-991-015, 409/TASK 52-11-21-991-016)
(a)
Remove and discard the lockwire from the nuts (142).
(b)
Loosen the nuts (142) and release the lockwashers (143).
1EFF : ALL 1 52-11-21Page 470 1 1 May 01/03R 1 1 1CES 1
(c) Turn the barrel of the rod (92) to get the connection.
(d) Install the bushes (93), (98) and the bolt (94).
(e) Install the washer (95) and the nut (96) and tighten it.
(f) Install a new cotter pin (97).
NOTE : If you install a new bolt (94), drill a hole of 2 mm____ (0.0787 in.) for the cotter pin installation.
(g) Tighten the nuts (142).
(h) Make sure that the lockwashers (143) are correctly positioned.
(i) Safety the nuts (142) and the lockwashers (143) with MISCELLANEOUS (Material No. 19-010).
(22) Adjustment of the upper stops.
(a) Make sure that the PIN - RIGGING (98D52103006000) is in position in the bellcrank assembly (125).
R R (b) Make sure that the kinematic stop (132) of the bellcrank assy (125) touches the door structure.
R (c) If not, adjust as follows:
1_ Loosen the nut (133).
2_ Remove and discard the lockwasher (134). Remove the washer (135).
R R 3_ Adjust the setscrew (136) until the kinematic stop (132) ofthe bellcrank assy (125) touches the door structure.
4_ Apply LUBRICANTS (Material No. 06-005) on the threads of the setscrew (136).
5_ Install the washer (135), the new lockwasher (134) and the nut (133).
6_ TORQUE the nut (133) to between 0.3 and 0.4 m.daN (26.54 and 35.39 lbf.in).
7_ Safety the nut (133) with the lockwasher (134).
1EFF : ALL 1 52-11-21Page 471 1 1 Feb 01/03 1 1 1CES 1
R (d) Put the lever assembly (122) in position until it touches the R bellcranck assy (123). Make sure that the clearance J6 is 0.5 +0 +0.1 mm (0.0196 +0.0000 +0.0039 in.).
(e) If the clearance J6 is not in the tolerances, adjust as follows: 1 Loosen the nut (133).
_ 2 Remove and discard the lockwasher (134). Remove the washer
_
(135).
3 Adjust the setscrew (136) to get the clearance.
_ 4 Apply LUBRICANTS (Material No. 06-005) on the threads of the
_
setscrew (136).
5 Install the washer (135), the new lockwasher (134) and the nut
_
(133).
6 TORQUE the nut (133) to between 0.3 and 0.4 m.daN (26.54 and
_
35.39 lbf.in). 7 Safety the nut (133) with the lockwasher (134).
_
(23)
Remove the PIN - RIGGING (98D52103006000).
(24)
Connect the rod (75).
(a)
Put the rod (75) in position in its fitting.
(b)
Install the bushes (71) and (72) with SPECIAL MATERIALS (Material No. 05-002), the washer (73) and the bolt (74).
(c)
Install the washer (70) and the nut (69).
(d)
TORQUE the nut (69) to between 0.6 and 0.7 m.daN (53.09 and 61.94 lbf.in).
(e)
Install a new cotter pin (68). NOTE : If you install a new bolt (74), drill a hole of 1.9 mm
____ (0.0748 in.) for the cotter pin installation.
(25) Check and adjustment of the locking hook (138) (Ref. TASK 52-11-21-820-001).
(a) Open the door and put two shims in the upper guide fittings.
1EFF : ALL 1 52-11-21Page 472 1 1 Feb 01/03 1 1 1CES 1
(b) Close the door.
(c) Adjust the locking hook (138) as follows: R 1_ Turn the barrel of the rod (75) until the locking hook (138)
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM DOORS 艙門2(4)
