(a)
 For the passenger/crew door 832 832AZ, 832BZ, 832CZ, 832DZ, 832EZ.

 (b)
 For the passenger/crew door 842 842AZ, 842BZ, 842CZ, 842DZ, 842EZ.

 (4)
 Remove the lining flap (Ref. TASK 52-13-31-000-001).

 (5)
 Remove the door insulation.

 1EFF : ALL 1 52-13-21Page 403 1 1 Feb 01/02 1 1 1CES 1R **ON A/C 003-049, 051-099, 101-149, 151-199, 201-299, 301-399, 401-499,

 Subtask 52-13-21-010-060-A
 C. Removal of Components
 (1)
 Remove the escape slide/raft (Ref. TASK 25-62-44-000-002).

 (2)
 Install the BALLAST WEIGHT - PASSENGER CREW DOOR (98D52103501000) (Ref. TASK 52-10-00-480-001).

 (3)
 Remove the door lining panels (Ref. TASK 25-23-46-000-002).

 (a)
 For the passenger/crew door 832 832AZ, 832BZ, 832CZ, 832DZ, 832EZ.

 (b)
 For the passenger/crew door 842 842AZ, 842BZ, 842CZ, 842DZ, 842EZ.

 (4)
 Remove the lining flap (Ref. TASK 52-13-31-000-001).

 (5) Remove the door insulation.
 **ON A/C ALL

 4. Procedure
_________
 Subtask 52-13-21-020-055

 A. Release the Compensation Mechanism: NOTE : It is necessary to release the tension of the torsion bar only for
____
 the removal of the outer control handle:

 -
the gearbox

 -
the upper and lower connection links

 -
the compensation mechanism

 -
the reducer shaft.

 (1)
 Remove the lockwire from the screw (1).

 (2)
 Loosen the screw (1) until the tension is released from the torsion bar.

 1EFF : ALL 1 52-13-21Page 404 1 1 Aug 01/05 1 1 1CES 1 Subtask 52-13-21-020-051

 B. Removal of the Outer Control Handle
 (Ref. Fig. 401/TASK 52-13-21-991-007)

 (1)
 Put the outer control handle in the open position until is locked.

 (2)
 Removal of the plate assembly.
 (Ref. Fig. 402/TASK 52-13-21-991-010)

 (a)
 Remove the screws (182) and (184) and the washers (183).

 (b)
 Remove the plate assy (181).

 (c)
 Clean the contact surface with CLEANING AGENTS (Material No. 11-004) and lint-free cloth.

 (3)
 Remove the cotter pin (195) and discard it.

 (4)
 Remove the nut (194) and the washer (193).

 (5)
 Push the shaft (191), disengage the outer control handle (192) and remove it.

 Subtask 52-13-21-020-052
 C. Removal of the Inner Control Handle
 (Ref. Fig. 403/TASK 52-13-21-991-006)

 (1)
 Remove the cotter pin (171) and discard it.

 (2)
 Remove the nut (172) and the washer (170).

 (3) Remove the inner control handle (173). Subtask 52-13-21-020-053
 D. Removal of the Gearbox
 (Ref. Fig. 404/TASK 52-13-21-991-008)

 (1) Removal of the plate assy
 (Ref. Fig. 402/TASK 52-13-21-991-010)

 (a)
 Remove the screws (182) (184) and the washers (183).

 (b)
 Remove the plate assy (181).

 1EFF : ALL 1 52-13-21Page 405 1 1 May 01/98R 1 1 1CES 1

 Outer Control Handle Figure 401/TASK 52-13-21-991-007
 1EFF : 1 1R 1CES  ALL  1 11 1 52-13-21 Page 406 May 01/98

 Plate Assembly Figure 402/TASK 52-13-21-991-010
 1EFF : 1 1R 1CES  ALL  1 11 1 52-13-21 Page 407 May 01/98

 Inner Control Handle
 Figure 403/TASK 52-13-21-991-006
 1EFF :  ALL  1  52-13-21 Page 408 
1  1  Feb 01/98
 1  1
 1CES  1

 Gearbox
 Figure 404/TASK 52-13-21-991-008
 1EFF :  ALL  1  52-13-21 Page 409 
1  1  Feb 01/98
 1  1
 1CES  1

 (c) Clean the contact surface with CLEANING AGENTS (Material No. 11-004) and a MISCELLANEOUS (Material No. 19-003).
 (2)
 Remove the inner and the outer control handles (222) and (238).

 (3)
 Remove the cotter pins (205) and discard them.

 (4)
 Remove the nuts (204), the washers (203) the bolts (210) and the
 washers (209).

 (5)
 Disengage the rods (207) and (223).

 (6)
 Remove the bushes (232), (233), (234) and (235).

 (7)
 Remove the cotter pin (220) and discard it.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門2(113)