(4)
If the contact is not correct:
(a) On the Z axis:
(Ref. Fig. 408/TASK 52-13-11-991-006)
1 Remove the lockwire from the nuts (101) and (103), and discard
_
it.
2 Loosen the nuts (101) and (103).
_ 3 Adjust the length of the rod (102) until you get the correct
_
configuration.
4 Tighten, the nuts (101) and (103), and safety the rod (102)
_ with MISCELLANEOUS (Material No. 19-010).
1EFF : ALL 1 52-13-11Page 424 1 1 Aug 01/05 1 1 1CES 1
Adjustment of the Door Stop Fittings Figure 407/TASK 52-13-11-991-016
1EFF : 1 1R 1CES ALL 1 11 1 52-13-11 Page 425 Feb 01/04
Clearances - Adjustments on Z Axis Figure 408/TASK 52-13-11-991-006
R 1EFF : 1 1 1CES ALL 1 111 52-13-11 Page 426 Feb 01/04
(b) On the X axis: (Ref. Fig. 403/TASK 52-13-11-991-005, 408/TASK 52-13-11-991-006)
1 Disconnect the upper and lower connection links (59) from each
_
side of the yoke (54).
2 Remove the nuts (57), the washers (58), (61) and the bolts
_
(60) to disconnect the upper and lower connection links (59). 3 Adjust the door in the X axis with the washers (62) of a
_
different thickness.
4 Make sure that the clearance B1 is less than or equal to 0.1
_
mm (0.0039 in.).
NOTE : The thickness of the two washers (62) at level of the
____ lower and upper connection links (59) is equal to the nominal thickness. Clearance B1 must be in the tolerances.
5 Connect the upper and lower connection links (59).
_
6 Install the washers (61), the bolts (60).
_
7 Install the washers (58) and the nuts (57).
_
(5) Make sure that when you start to open the door the clearance H1 between the door stops (111) and the door frame stops (112) is 5 mm (0.1968 in.) minimum.
R **ON A/C 001-049, 051-061, 101-104, 201-203,
Subtask 52-13-11-820-052
C. Adjustment of the Door in its Frame During the Door Closing Operation (Ref. Fig. 406/TASK 52-13-11-991-011, 407/TASK 52-13-11-991-016, 409/TASK 52-13-11-991-019, 410/TASK 52-13-11-991-012)
(1)
Slowly close the door and make sure that there is no hard contact between the door stops (101) and the frame stops (112). (Ref. Fig. 411/TASK 52-13-11-991-008)
(2)
The clearance H2 must be 0.2 mm minimum for an overlap H3 of 3 mm (0.1181 in.) to 4 mm (0.1574 in.). The guide rollers (81) are in contact with the guide fittings (82) and (86).
1EFF : ALL 1 52-13-11Page 427 1 1 May 01/05 1 1 1CES 1
Adjustment of the Upper Hook
Figure 409/TASK 52-13-11-991-019
R 1EFF : 001-049, 051-099, 101-105, 151-154, 1 52-13-11Page 428 1201-207, 1May 01/05 1 1 1CES 1
INTENTIONALLY BLANK
R 1 1
52-13-11Page 429
1 1 Feb 01/04 1 1 1CES 1
Adjustment of the Upper Hook
Figure 409A/TASK 52-13-11-991-019-A12 (SHEET 1)
R 1EFF : 106-149, 155-199, 208-299, 301-399, 1 52-13-11Page 430 1401-499, 1Aug 01/05 1 1 1CES 1
Adjustment of the Upper Hook
Figure 409A/TASK 52-13-11-991-019-A22 (SHEET 2)
R 1EFF : 106-149, 155-199, 208-299, 301-399, 1 52-13-11Page 431 1401-499, 1Aug 01/05 1 1 1CES 1
Girt Bar Fittings - Clearances and Adjustments Figure 410/TASK 52-13-11-991-012
1EFF : 1 1R 1CES ALL 1 11 1 52-13-11 Page 432 Feb 01/04
INTENTIONALLY BLANK
R 1 1
52-13-11Page 433
1 1 Feb 01/04 1 1 1CES 1
Adjustment of the Door on the Door Frame Figure 411/TASK 52-13-11-991-008- 13 (SHEET 1)
1EFF : 1 1R 1CES ALL 1 11 1 52-13-11 Page 434 Feb 01/04
Adjustment of the Door on the Door Frame Figure 411/TASK 52-13-11-991-008- 23 (SHEET 2)
1EFF : 1 1R 1CES ALL 1 11 1 52-13-11 Page 435 Feb 01/04
Adjustment of the Door on the Door Frame Figure 411/TASK 52-13-11-991-008- 33 (SHEET 3)
1EFF : 1 1R 1CES ALL 1 11 1 52-13-11 Page 436 Feb 01/04
(3)
If the clearance H2 is not in the tolerances, adjust the upper and lower guide fittings (82) and (86) as follows:
(a)
Open the door and identify the position of the serration plates
(89) and (90), and the upper and lower guide fittings (82), (86).
(b)
Loosen the screws (80) and move the guide fittings (82), (86) to get the clearance H2 and temporarily tighten the screws (80).
(4)
Release the upper hook as follows:
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門2(81)
