A. Make sure that the ground service network is energized (Ref. TASK 24-42-00-861-001).
Subtask 27-92-41-010-070
B. Get Access
(1)
Make sure that the access platform is in position at the access door
822.
(2)
Make sure that the access door 822 is open.
(3)
On the battery power center 105VU:
-make sure that the protective cover is removed.
Subtask 27-92-41-865-059
C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/ELAC1/NORM/SPLY 15CE1 B11 49VU FLIGHT CONTROLS/SEC1/NORM/SPLY 21CE1 B08 49VU COM/AUDIO/ACP/F/O 5RN G07 49VU COM/AUDIO/ACP/CAPT 4RN G06 105VU FLIGHT CONTROLS/ELAC2/STBY SPLY 16CE2 A02 105VU FLT CTL/ELAC1/STBY SPLY 16CE1 A01 105VU FLT CTL/SEC1/STBY SPLY 22CE B01 121VU AUTO FLT/STICK/LOCK 13CA N16 121VU FLIGHT CONTROLS/SEC3/SPLY 21CE3 Q19 121VU FLIGHT CONTROLS/SEC2/SPLY 21CE2 Q18 121VU FLIGHT CONTROLS/ELAC2/NORM/SPLY 15CE2 R20
Subtask 27-92-41-860-051
D. Aircraft Maintenance Configuration
(1)
Make sure that the cover of the panel 18VU (19VU) is removed.
(2)
Make sure that PIN-SIDE STICK LOCKING (98D27903500000) is installed.
(3)
Make sure that the warning notice which tells persons not to operate the side stick is in position.
4. Procedure_________
(Ref. Fig. 412/TASK 27-92-41-991-012)
Subtask 27-92-41-210-052
A. Make sure that no foreign material has gone into the opening before you install the bellows (90).
1EFF : ALL 1 27-92-41Page 466 1 1 May 01/04R 1 1 1CES 1
Subtask 27-92-41-420-058
B. Installation of the Bellows
(1)
Install the bellows (90), fold it over the handle (91) and attach it with a ligature cord (89) as follows:
(a)
Put the ligature cord (89) around the bellows (90) twice.
(b)
Tighten the ligature cord (89) and attach it.
(c)
Bond the knot with BONDING AND ADHESIVE COMPOUNDS (Material No. 08-004).
(2)
Install the bellows (90) on the support (92) and attach it with a ligature cord as follows:
(a)
Put the ligature cord (89) around the bellows (90) twice.
(b)
Tighten the ligature cord (89) and attach it.
(c)
Bond the knot with BONDING AND ADHESIVE COMPOUNDS (Material No. 08-004).
5. Close-up
________ R **ON A/C 001-049, 051-099, 101-105, 151-158, 201-210,
Subtask 27-92-41-410-058
A. Remove the PIN-SIDE STICK LOCKING (98D27903500000) (93) and the warning notice from the side stick. (Ref. Fig. 412/TASK 27-92-41-991-012)
(1)
Installation of the cover of the panel 19VU (18VU). (Ref. Fig. 401/TASK 27-92-41-991-001)
(2)
Put the cover (3) in position.
(3)
Install the washers (5), the washer (7), the screws (4) and the screw (6). Tighten the screws. Lock the catches (2).
(4)
Release the lock (8). Install the handle (1).
R **ON A/C 106-149, 159-199, 211-299, 301-399, 401-499,
Subtask 27-92-41-410-058-A
A. Remove the PIN-SIDE STICK LOCKING (98D27903500000) (93) and the warning notice from the side stick. (Ref. Fig. 412/TASK 27-92-41-991-012)
(1)
Installation of the cover of the panel 19VU (18VU).
(Ref. Fig. 401A/TASK 27-92-41-991-001-A)
(2)
Put the cover (3) in position.
(3)
Install the screws (2) and tighten them.
(4)
Install the washers (5), the washer (7), the screws (4) and the screw (6). Tighten the screws.
(5) Install the handle (1) and the screws (8). Tighten the srcews. **ON A/C ALL
Subtask 27-92-41-865-060
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 15CE1, 15CE2, 16CE1, 16CE2, 21CE1, 21CE2, 21CE3, 22CE, 13CA, 4RN, 5RN
Subtask 27-92-41-942-052
C. Make sure that the work area is clean and clear of tool(s) and other items.
Subtask 27-92-41-862-054
D. De-energize the ground service network
(Ref. TASK 24-42-00-862-001).
Subtask 27-92-41-410-067 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱9(55)
