-an input lever with stops for stroke limitation.
 -
two resolvers for engine control, electrically connected to the
 relevant FADEC.

 -
two sets of three plastic track potentiometers electrically connected to the SECs.

 -A duplicate drive system for transducers.
 -Four electrical plugs.
 -
The input lever zero position is accurately determined by a rigging pin between input lever and body. The potentiometers are rigged to mid stroke and resolvers to zero for this input lever position which corresponds to idle selection.

 -
The design is such that no single mechanical failure is able to cause the loss of the two potentiometer sets without loss of resolver drive.

 -Potentiometer sets are the same as those fitted in SPD BRK control transducer unit and in side stick transducer unit.
 -Each SEC control and monitoring unit receives signals from two potentiometers of the same unit, one of each set of potentiometer (to enable detection of a potentiometer drive rupture). Electrical characteristics of potentiometers are monitored by SECs as previously described for the other potentiometers. (Ref. Fig. 020) This figure shows mechanical liaison between the control unit and throttle levers on the center pedestal. (Ref. Fig. 021)

R  Throttle Control Unit Figure 019
 1EFF : 1 1 1CES  ALL  1 111 27-92-00 Page 28 Aug 01/04

R  Throttle Control Levers Figure 020
 1EFF : 1 1 1CES  ALL  1 111 27-92-00 Page 29 Aug 01/04

R  R Throttle Control Unit - Wiring Diagram Figure 021
 1EFF : 1 1 1CES  ALL  1 111 27-92-00 Page 30 Aug 01/04

 TRANSDUCER UNIT - ELEVATOR POSITION (49CE1,49CE2) - REMOVAL/INSTALLATION
________________________________________________________________________ TASK 27-92-13-000-001 Removal of the Elevator Servocontrol Position Transducer Unit 49CE1, 49CE2 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
 WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE CLEAR.
_______ MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
 WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROL SURFACES ARE
_______ CLEAR BEFORE YOU PRESSURIZE/DEPRESSURIZE A HYDRAULIC SYSTEM.
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE. WARNING : WEAR AND ATTACH A SAFETY HARNESS WHEN YOU WORK ON HIGH SECTIONS. A
_______ FALL CAN INJURE OR KILL YOU.
 CAUTION : DO NOT CAUSE DAMAGE TO THE SURFACES. THE COMPONENTS ARE MADE OF
_______ CARBONFIBER REINFORCED PLASTIC.
 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking caps No specific circuit breaker(s) safety clip(s) No specific warning notices No specific access platform 3.5 m (11 ft. 6 in.) 98D27903500000 1 PIN-SIDE STICK LOCKING
 1EFF : ALL 1 27-92-13Page 401 1 1 May 01/00R 1 1 1CES 1

 B. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
29-10-00-863-001 Pressurize the Green Hydraulic System
 29-10-00-863-002 Pressurize the Yellow Hydraulic System
R 29-10-00-863-003 Pressurize the Blue Hydraulic System with a Ground
R Power Supply 55-13-11-000-001 Removal of the THS Trailing Edge Access Panels 27-92-13-991-001 Fig. 401
 3. Job Set-up
__________
 Subtask 27-92-13-860-051
 A. Aircraft Maintenance Configuration
 (1)
 Make sure that the elevators and the trimmable horizontal stabilizer controls are set to the neutral position.

 (2)
 Engange ELAC 2

 Subtask 27-92-13-860-050
 B. Pressurize Hydraulic Systems
 (1) Pressurize the Green, Yellow, and Blue hydraulic systems. (Ref. TASK 29-10-00-863-001) (Ref. TASK 29-10-00-863-002) (Ref. TASK 29-10-00-863-003)
 Subtask 27-92-13-865-050
 C. Open, safety and tag this(these) circuit breaker(s):
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱9(15)