LRU Identification
 Figure 008
 1EFF :  ALL  1  27-96-00 Page 11 
1  1  Feb 01/98
 1  1
 1CES  1

 Ground Scan
 Figure 009
 1EFF :  ALL  1  27-96-00 Page 12 
1  1  Feb 01/98
 1  1
 1CES  1

 TROUBLE SHOOTING DATA from
 LAST LEG REPORT
 Figure 010
 1EFF :  ALL  1  27-96-00 Page 13 
1  1  Feb 01/98
 1  1
 1CES  1

 TROUBLE SHOOTING DATA from
 PREVIOUS LEG REPORT
 Figure 011
 1EFF :  ALL  1  27-96-00 Page 14 
1  1  Feb 01/98
 1  1
 1CES  1

 TROUBLE SHOOTING DATA : EFCS STATUS
 Figure 012
 1EFF :  ALL  1  27-96-00 Page 15 
1  1  Feb 01/98
 1  1
 1CES  1

R  4. Test____ 
R  This function is presented on the MCDU by the FCDCs. It has two purposes: 
R  - initiate tests related to flight controls, 
R  - display the test results on the MCDU. 
R  Two tests are available: 
R  - elevator servocontrol damping test 
R  - aileron servocontrol damping test 
R  A. Elevator servocontrol damping test 
R  (Ref. Fig. 013) 
R  This test is initiated from the MCDU : indications given by the MCDU 
R  provide guidance to conduct the test. 
R  The test is driven by the FCDC and is performed by the SEC1 and SEC2. 
R  The SECs control the deflections of the surfaces by pressurizing each 
R  servocontrol simultaneously then alternatively. 
R  - If the test is possible 
R  For each movement, the FCDC memorizes a deflection speed and a pressure 
R  drop, then it deducts a damping coefficient. 
R  The test result is displayed on the MCDU in the form L ELEV TEST OK or 
R  R ELEV TEST OK. 
R  The value of the damping coefficient can be obtained and displayed 
R  through the TEST REPORT. 
R  - If the test is not possible 
R  The test result is displayed on the MCDU in the form ELEV TEST NOT 
R  POSSIBLE. 
R  The computer which have identified the anomaly, and the engagement 
R  condition code are displayed on the MCDU. 
R  (Ref. Fig. 014) 
R
 B. Aileron servocontrol damping test
 (Ref. Fig. 015)
 The test is conducted in the same manner as the elevator servocontrol
 test.
 The test is driven by the FCDC and performed by the two ELACs.
 - If the test is possible
 Measurements identical with that on elevators are performed.
 The test result is displayed on the MCDU in the form R AIL TEST OK or L
 AIL TEST OK.
 The value of the damping coefficient can be obtained and displayed
 through the TEST REPORT.
 - If the test is not possible
 The test result is displayed on the MCDU in the form AIL TEST NOT
 POSSIBLE.
 The computer which have identified the anomaly, and the engagement
 condition code are displayed on the MCDU.

R  Elevator Servocontrol Damping Test Figure 013
 1EFF : 1 1 1CES  ALL  1 111 27-96-00 Page 17 Feb 01/02

R  Elevator Test not possible Figure 014
 1EFF : 1 1 1CES  ALL  1 111 27-96-00 Page 18 Feb 01/02

 Aileron Servocontrol Damping Test
 Figure 015
 1EFF :  ALL  1  27-96-00 Page 19 
1  1  Feb 01/98
 1  1
 1CES  1

 -ground condition
 -ADR OFF
 -wheel speed < 6kts
 -both FCDCs available
 NOTE : When a test is not possible on hexa code is display on the
____ MCDU in order to help the operator. When the FCDC is in MENUE mode. the FCDC FAULT warning is displayed on the upper ECAM. (Ref. Fig. 014, 016)

R  Ail Test not possible Figure 016
 1EFF : 1 1 1CES  ALL  1 111 27-96-00 Page 21 May 01/00
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱9(113)