曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

R  NOTE : The flap, tab and slat angles are in degrees.____
R The slat/flap control lever has two baulks. One baulk between position 1 R and 2, and one between position 3 and FULL. The baulks prevent a R one-movement-change of the lever position from FULL to 0. The lever turns R a shaft which moves the input shaft of the CSU through spur gears.
 **ON A/C ALL
 B. Electrical Control
 (Ref. Fig. 004)
 The CSU is installed in the cockpit, immediately below the slat and flap control lever on the panel 114VU. The CSU changes the mechanical signals from the control lever into electrical signals to the SFCC1 and SFCC2.
 The two SFCCs are installed in racks in the forward avionics compartment. The SFCCs have power supplies with no relation between them. Each SFCC has the same function and includes one flap channel and one slat channel. The flap channels each control one of the two valve blocks on the flaps PCU. Each valve block has its own different hydraulic supply (Ref. 27-54-00).

 Flaps Electrical Control - Schematic Figure 004
 1EFF : 1 1R 1CES  ALL  1 11 1 27-51-00 Page 8 Feb 01/00

 

 There are three solenoid valves at each valve block. For the low speed mode, the SFCCs energize the retract/extend solenoid valves and the POB solenoid. For the high speed mode, the SFCCs energize the extend solenoid valve and the POB solenoid. The POB solenoid permits the release of the POB of the hydraulic motor (Ref. 27-84-00).
 An FPPU, which is attached to the PCU, sends signals on the position of the flap transmission to the two SFCCs. The PCU gearbox moves the FPPU. The FPPU has two synchro transmitters, which are the same. One sends signals to the SFCC1, the other one to the SFCC2.
 C. Wing Tip Brake (WTB) Control
 (Ref. Fig. 005)
 The WTB is an electro-hydraulic pressure-on brake. It is installed near the end of the transmission system in each wing. The WTBs stop and hold the transmission if the SFCCs find some given types of failures. Each WTB has two solenoid valves. Each solenoid valve controls one part of a WTB. The hydraulic supply to each WTB is as follows:
 -
the Blue and Yellow systems supply the left WTB

 -
the Blue and Green systems supply the right WTB.

 The two battery buses (701PP for system 1 and 702PP for system 2) supply power to the WTB solenoids through the SFCCs. This makes sure that power is available to the WTB if there is an engine power failure. Each busbar supplies one solenoid on each WTB. When the solenoids are energized, the system latches the circuit to keep the solenoid valves open. When the WTBs operate, the transmission locks. The circuit can only be set back (reset) on the ground through the Centralized Fault Display System (CFDS).
 The two SFCCs control the LH and the RH WTB. Each SFCC controls one solenoid on each WTB.
 D. Monitoring
 (Ref. Fig. 006)
 The two SFCCs monitor the flap system continuously for failures in:
 -
the operation of the power transmission system

 -
the Line Replaceable Units (LRU)

 -
the input and output signals

 -
the power supplies.

 1EFF : ALL 1 27-51-00Page 9 1 1 May 01/04R 1 1 1CES 1

 Wing Tip Brake (WTB) Control - Schematic Figure 005
 1EFF : 1 1R 1CES  ALL  1 11 1 27-51-00 Page 10 May 01/04

 

 Flap Transmission Monitoring - Schematic Figure 006
 1EFF : 1 1R 1CES  ALL  1 11 1 27-51-00 Page 11 Feb 01/00

 

 Failures in the flap system will not give, but may lead to class 1 level 3 warnings which are generated by the Electronic Centralized Aircraft Monitoring (ECAM) system.
 The ECAM system shows class 1, level 1 and level 2 cautions to the flight crew (Ref. 31-50-00). The SFCCs supply failure data to the ECAM system through:
 -
the System Data Acquisition Concentrators (SDAC) (Ref. 31-55-00)

 -
the Flight Warning Computers (FWC) (Ref. 31-53-00)

 -
the Display Management Computers (DMC) (Ref. 31-62-00).

 The ECAM gives a Maintenance Status Reminder for class 2 failures.
 The SFCCs supply all the related data of failures to the Centralized Fault Display System (CFDS).
 (1) Monitoring of the Power Transmission Systems
 The SFCCs monitor the power transmission system for these failures:
 -asymmetry (a position difference between the two APPUs)
 -runaway (a position difference between the APPUs and the FPPU)
 -uncommanded movement (a movement in the wrong direction, or
 movement away from the last set position)
 - overspeed (the faster movement of one or more PPUs)

 -flap disconnect
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱4(8)