Rigging Kit Installation - Inboard Flap
 Figure 523B/TASK 27-51-00-991-073-B12 (SHEET 1)

R 1EFF : 062-099, 104-149, 151-199, 204-299, 1 27-51-00Page A560 1401-499, 1Aug 01/05 1 1 1CES 1

 Rigging Kit Installation - Inboard Flap
 Figure 523B/TASK 27-51-00-991-073-B22 (SHEET 2)

R 1EFF : 062-099, 104-149, 151-199, 204-299, 1 27-51-00Page A561 1401-499, 1Aug 01/05 1 1 1CES 1

 Main Eccentric Bearing Adjustment - Track 1
 Figure 524/TASK 27-51-00-991-074- 12 (SHEET 1)

R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 27-51-00Page A562 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1

 Main Eccentric Bearing Adjustment - Track 1
 Figure 524/TASK 27-51-00-991-074- 22 (SHEET 2)

R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 27-51-00Page A563 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1

 (2) At the track 2 position set the main eccentric bearing to the zero datum position as follows:
 (Ref. Fig. 521/TASK 27-51-00-991-071)
 (a)
 Remove and discard the lockwire from the nuts (57) installed on the failsafe hooks.

 (b)
 Loosen the nuts (57). NOTE : These are loosened to give easier movement when the

____ eccentric bearings are adjusted.

 (c)
 Remove and discard the cotter pin (54) from the nut (53).

 (d)
 Remove these items:

 -
the nut (53)

 -
the crushable spacer (52)

 -
the nut (55) and the washer (56)

 -
the locking plate (51).

 (e)
 Engage the TOOL - FLAP ADJUSTING, (98D27504082000) with the splined bush in the flap carriage.

 (f)
 Turn the splined bush until the red paint marks are aligned. NOTE : The splined bush engages with the main eccentric bearing.

____ When the bush is turned the eccentric bearing also turns.

R **ON A/C 062-099, 104-149, 151-199, 204-299, 401-499,
 Subtask 27-51-00-820-075-A
 H. Set the Main Eccentric Bearings of the Inboard Flap to the Zero Datum Position
 (Ref. Fig. 521/TASK 27-51-00-991-071, 524/TASK 27-51-00-991-074) NOTE : The main eccentric bearings are spherical bearings installed in
____ the flap attachment fittings at the flap carriages.
 At track 1, an eccentric bush (86) is installed in the bearing (87). A pin on the eccentric bush (86) engages with the toothplate (85). The bearing (87) is at zero datum when the pin on the eccentric bush (86) is at the position shown (Ref. Fig. 524/TASK 27-51-00-991-074)
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 27-51-00Page A564 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1

 Detail D.

 At track 2, red paint marks on the bearing and on the fitting show
 the zero datum position. The bearing is at the zero datum position
 when the red paint marks are aligned.
 (Ref. Fig. 521/TASK 27-51-00-991-071)

 Adjust the bearings at one position then the other in small
 increments.

 (1)
 At the track 1 position set the main eccentric bearing to the zero datum position as follows:

 (a)
 Remove and discard the lockwire from the bolt (80).

 (b)
 Remove these items:

 -
the bolt (80)

 -
the washer (81)

 -
the stop (82)

 -
the nut (83)

 -
the lockwasher (84)

 -
the toothplate (85).

 (c) Use the TOOL FLAP ADJUSTING (98D27504041000) to move the
 eccentric bush (86) to the position shown.
 (Ref. Fig. 524/TASK 27-51-00-991-074)
 Detail D.

 (2)
 At the track 2 position set the main eccentric bearing to the zero datum position as follows:

 (Ref. Fig. 521/TASK 27-51-00-991-071)
 (a)
 Remove and discard the lockwire from the nuts (57) installed on the failsafe hooks.

 (b)
 Loosen the nuts (57).

 NOTE : These are loosened to give easier movement when the
____
 eccentric bearings are adjusted.

 (c)
 Remove and discard the cotter pin (54) from the nut (53).

 (d)
 Remove these items:

 -
the nut (53)

 -
the crushable spacer (52)

 -
the nut (55) and the washer (56)

R 1EFF : 062-099, 104-149, 151-199, 204-299, 1 27-51-00Page A565 1401-499, 1Aug 01/05 1 1 1CES 1 -the locking plate (51).

 (e)
 Engage the TOOL - FLAP ADJUSTING, (98D27504082000) with the splined bush in the flap carriage.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱4(74)