(2)
 Get access to the SYSTEM REPORT/TEST F/CTL page on the Multipurpose Control Display Unit (MCDU) (Ref. TASK 31-32-00-860-006).

 Subtask 27-51-00-865-062
R C. Make sure that this(these) circuit breaker(s) is(are) closed:
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 49VU FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1 5CV B06 121VU FLIGHT CONTROLS/WTB/FLP/SYS2 12CV P20 121VU FLIGHT CONTROLS/WTB/SLT/SYS2 11CV P19 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21 121VU FLIGHT CONTROLS/SLT/CTL/SYS2 7CV R21 122VU FLIGHT CONTROLS/WTB/FLP/SYS1 10CV S07 122VU FLIGHT CONTROLS/WTB/SLT/SYS1 9CV S06

 4. Procedure
_________
 Subtask 27-51-00-740-050-A
 A. BITE Test of the Slat and Flap Control Computer (Flap System)
 NOTE : Use the Multipurpose Control Display Unit (MCDU) 2 on panel 11VU
____
 for the test.

 -------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the Multipurpose Control  On the MCDU:
 Display unit (MCDU): - the MCDU shows the SFCC 1 menu.

 -push the line key < SFCC 1.
 2. On the MCDU:  On the MCDU:
 -push the NEXT PAGE button.  - the MCDU shows the next page of the SFCC 1 menu.
 3. On the MCDU:  On the MCDU:
 -push the line key TEST/RESET  - the MCDU shows the SFCC 1 FLAP FLP>. TEST/RESET menu.
 4. On the MCDU:  - the MCDU shows SFCC 1
R  - push the line key < SFCC TEST. FLAP SFCC TEST IN PROGRESS
 -
for a positive test result the MCDU shows SFCC 1 FLAP SFCC TEST NO FAULTS

 -
for a negative test result, the MCDU shows SFCC 1 FLAP SFCC TEST PERFORMED WITH FAULT <FAULT DATA (push the line key <FAULT DATA to show the the failure data)

 -if the test finds a peripheral fault, the MCDU shows SFCC 1 FLAP SFCC TEST NO FAULTS BUT (for a peripheral fault see the display below).
 5. On the MCDU:

 -------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------
-push the line key < RETURN
 frequently until the MCDU shows
 the SYSTEM REPORT/TEST
 F/CTL menu.

 6. On the MCDU: On the MCDU:
 -push the line key < SFCC 2. - the MCDU shows the SFCC 2 menu.
 7.
 Do the SFCC test as described above with the SFCC 2 menu.

 8.
 On the MCDU:

 -push the line key < RETURN
 frequently until the CFDS menu
 page is shown.

 If there is a peripheral fault, the SFCC TEST RESULT page will be shown on the CFDS.
 SFCC 1 FLAP SFCC TEST
 DATE:XXX XX UTC:XXXX
 1L -|NO FAULTS BUT |- 1R
 | |
 2L -|* |- 2R
 | |
 3L -|** |- 3R
 | |
 4L -| |- 4R
 | |
 5L -| |- 5R
 | |
 6L -|<RETURN PRINT>|- 6R

 NOTE : "*" If the X-computer arm test is not done during the TEST these
____
 words will be shown:

 1EFF : ALL 1 27-51-00Page 506 1 1 Feb 01/01R 1 1 1CES 1

 2L -|OTHER SFCC ARM SIGNAL|- 2R |NOT TESTED |
 NOTE : "**" Shows one or more of the peripheral faults or a system is not
____ complete as follows:
 either  |WTB SET  |
 |  |
 and/or  |NO WTB POWER  |
 |  |
 and/or  |LH WTB SOLENOID X/X  |
 |  |
 and/or  |RH WTB SOLENOID X/X  |
 |  |
 and/or  |FPPU FAULT  |
 |  |
 and/or  |LH APPU FAULT  |
 |  |
 and/or  |RH APPU FAULT  |

 NOTE : "X/X" shows S/C short circuit or O/C open circuit.
____
 ________

5. Close-up
 Subtask 27-51-00-862-051
 A. Aircraft Configuration
 (1) De-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-002).
 Subtask 27-51-00-942-075
 B. Removal of Equipment
 (1)
 Make sure that the work area is clean and clear of tool(s) and other items.
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM FLIGHT CONTROLS 飛行操縱4(39)