R 1EFF : 301-399, 1 27-51-00Page 559 1 1 May 01/04 1 1 1CES 1
Installation of the Flap Rigging Kit
Figure 504/TASK 27-51-00-991-018
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 27-51-00Page 560 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1 **ON A/C 002-049, 053-061, 101-105, 201-203,
Subtask 27-51-00-480-051-A
A. Installation of the Rigging Tools (Ref. Fig. 505/TASK 27-51-00-991-055, 506/TASK 27-51-00-991-056)
(1)
Install the PIN RIGGING-FLAPS (TRACK 1) (98D27504005000) (1) at the track 1 position only.
(2)
Install the PIN RIGGING FLAPS (98D27504006000) (2) at the track 2, 3 and 4 positions.
(3)
Install the KIT-FLAP RIGGING (98D27504038001):
-
for the inboard flap, on the flap track 2 beam assembly
-
for the outboard flap, on the flap track 3 beam assembly.
(a)
Install the base assembly (15) on the flap track beam (18). Make sure that the aft dowels (14) touch the track beam end-stop (13).
(b)
Move the two lower clamps (16) into position below the flap track beam (18) and tighten the knurled screws (17).
(c)
Move the fin (11) into position on the base assembly (15) and install the pin (12). Install the scale block (19) in position on the fin (11).
R **ON A/C 051-052, 062-099, 106-149, 151-199, 204-299, 401-499,
Subtask 27-51-00-480-051-B
A. Installation of the Rigging Tools (Ref. Fig. 505/TASK 27-51-00-991-055, 506A/TASK 27-51-00-991-056-A)
(1)
Install the PIN RIGGING-FLAPS (TRACK 1) (98D27504005000) (1) at the track 1 position only.
(2)
Install the PIN RIGGING FLAPS (98D27504006000) (2) at the track 2, 3 and 4 positions.
R 1EFF : 002-049, 051-099, 101-149, 151-199, 1 27-51-00Page 561 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
R Installation of the Flap Rigging Kit
R Figure 504A/TASK 27-51-00-991-018-A
R 1EFF : 301-399, 1 27-51-00 Page 562
1 1 May 01/04
1 1
1CES 1
R Installation of the Flap Rigging Pins Figure 505/TASK 27-51-00-991-055
R 1EFF : 002-049, 051-099, 101-149, 151-199, 1 27-51-00Page 563 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
R Installation of the Flap Rigging Pins
R Figure 505A/TASK 27-51-00-991-055-A
R 1EFF : 301-399, 1 27-51-00 Page 564
1 1 May 01/04
1 1
1CES 1
Installation of the Flap Rigging Kit
Figure 506/TASK 27-51-00-991-056
R 1EFF : 002-049, 053-061, 101-105, 201-203, 1 27-51-00Page 565 1 1 May 01/05 1 1 1CES 1
Installation of the Flap Rigging Kit
Figure 506A/TASK 27-51-00-991-056-A
R 1EFF : 051-052, 062-099, 106-149, 151-199, 1 27-51-00Page 566 1204-299, 401-499, 1Aug 01/05 1 1 1CES 1
(3) Install the KIT-FLAP RIGGING (98D27504038001):
-
for the inboard flap, on the flap track 2 beam assembly
-
for the outboard flap, on the flap track 3 beam assembly and on the flap track 4 assembly.
(a)
Install the base assembly (15) on the flap track beam (18). Make sure that the aft dowels (14) touch the track beam end-stop (13).
(b)
Move the two lower clamps (16) into position below the flap track beam (18) and tighten the knurled screws (17).
(c)
Move the fin (11) into position on the base assembly (15) and install the pin (12). Install the scale block (19) in position on the fin (11).
**ON A/C 301-399,
Subtask 27-51-00-480-051-C
A. Installation of the Rigging Tools
(Ref. Fig. 505A/TASK 27-51-00-991-055-A, 506B/TASK 27-51-00-991-056-B)
(1)
Install a PIN RIGGING FLAPS (98D27504006000) (1) at each actuator lever position.
(2)
Install the KIT-FLAP RIGGING (98D27504113001):
-
for the inboard flap, on the flap track 2 beam assembly
-
for the outboard flap, on the flap track 3 beam assembly and on the flap track 4 beam assembly.
(a)
Install the base assembly (15) on the flap track beam (18). Make sure that the aft dowels (14) touch the track beam end-stop (13).
(b)
Move the two lower clamps (16) into position below the flap track beam (18) and tighten the knurled screws (17).
(c)
Move the fin (11) into position on the base assembly (15) and install the pin (12). Install the scale block (19) in position on the fin (11).
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱4(55)
