R R (5) At the track 3 position, temporarily install the serrated plate (2) with the bolt (1), the washer (3) and the nut (4).
R R (6) At the track 4 position, temporarily install the serrated plate (9) with the bolt (7) and the washer (8).
R R (7) Make sure that the punched/painted marks on the forward eccentrics align.
R R (8) Remove the sharks fin flap rigging kit (Ref. TASK 27-51-00-820-008) or (Ref. TASK 27-51-00-820-009).
R **ON A/C ALL
5. Close-up________
Subtask 27-51-00-942-068
A. Removal of Equipment
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Remove the safety barriers.
(3) Remove the warning notice(s).
(4) Remove the access platform(s).
(5) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
R 1EFF : ALL 1 27-51-00Page A500 1 1 Aug 01/05 1 1 1CES 1R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
TASK 27-51-00-820-008
Adjustment of the Flap Rigged Position With the Sharks Fin Tool (A318/319/320)
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Flap rigging is done:
-
when specified in an AMM Task
-
when specified in a TSM Task
-if you think the the flap rigged position is incorrect.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 27-51-00Page A501 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific ruler-steel
No specific safety barriers
No specific warning notice
No specific access platform 3 m (9 ft. 10 in.)
No specific Torque Wrench : range 0.00 to 1.20 m.daN
(0.00 to 9.00 lbf.ft)
No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft)
No specific Torque Wrench : range 1.00 to 10.00 m.daN
(8.00 to 75.00 lbf.ft)
No specific Torque Wrench : range 2.00 to 20.00 m.daN
(15.00 to 150.00 lbf.ft)
98D27504002000 1 TOOL-FLAP ADJUSTING
98D27504005000 2 PIN RIGGING-FLAPS (TRACK 1)
98D27504006000 3 PIN RIGGING FLAPS
98D27504030001 1 LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT
98D27504035000 1 TORQUE ADAPTOR-TRUNNION NUT
98D27504038000 3 KIT-FLAP RIGGING
98D27504038001 3 KIT-FLAP RIGGING
98D27504039000 1 TOOL RESTRAINING TK1
98D27504040000 1 TOOL RESTRAINING TK1
98D27504041000 1 TOOL FLAP ADJUSTING
98D27504082000 2 TOOL - FLAP ADJUSTING,
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱4(62)
