Inboard Flap Rigging Dimensions
 Figure 508A/TASK 27-51-00-991-057-A 
R 1EFF :  301-399,  1  27-51-00 Page 574 
1  1  Feb 01/05
 1  1
 1CES  1

 **ON A/C 001-001,
 Subtask 27-51-00-220-057-B
R C. To Do a Check of the Outboard Flap Rigged Position
 (Ref. Fig. 509/TASK 27-51-00-991-022, 510/TASK 27-51-00-991-023, 511/TASK
 27-51-00-991-060)
 NOTE : The tolerances given in the work steps that follow are in-service
____ tolerances only. They are not initial adjustment tolerances.
 The tolerances for initial adjustment are given in the flap rigged R position adjustment procedure (Ref. TASK 27-51-00-820-008).
 (1) At the track 3 position, measure:
 (a) The dimension P (between the bottom of the trailing edge and the fin (40)).
 1 Check the value shown on the label (42) attached to the
_ outboard side of the flap track 3 beam.
 2 If the value on the label (42) is '0', the dimension P must be
_ 10 mm (0.4 in.) +/- 1.5 mm (0.06 in.).
 3 If the label (42) shows a plus value, subtract the value from
_ the dimension P. The remaining value must be 10 mm (0.4 in) +/- 1.5 mm (0.06 in.).
 4 If the label (42) shows a minus value, add the value to the
_ dimension P. The remaining value must be 10 mm (0.4 in) +/-
1.5 mm (0.06 in.).
 (b) The dimension N (between the end of the trailing edge and the fin (40)), this must be 20 mm (0.8 in.) +/- 5 mm (0.2 in.), measured from the inboard side of the fin (40).
 (2) At the outboard end of the flap, measure:
 (a) The dimension R (the horizontal measurement between the outer fixed shroud and the outboard end of the flap). This must be zero +/- 5 mm (0.2 in.).
R 1EFF : 001-001, 1 27-51-00Page 575 1 1 Feb 01/05 1 1 1CES 1

 Outboard Flap Rigging Dimensions (Sheet 1)
 Figure 509/TASK 27-51-00-991-022

R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 27-51-00Page 576 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1

 Outboard Flap Rigging Dimensions (Sheet 1)
 Figure 509A/TASK 27-51-00-991-022-A

R 1EFF : 301-399, 1 27-51-00Page 577 1 1 Feb 01/05 1 1 1CES 1

 Outboard Flap Rigging Dimensions (Sheet 2)
 Figure 510/TASK 27-51-00-991-023

R 1EFF : 001-049, 053-061, 101-105, 201-203, 1 27-51-00Page 578 1 1 May 01/05 1 1 1CES 1

 Label Position - Flap Track Beam
 Figure 511/TASK 27-51-00-991-060

R 1EFF : 001-049, 053-099, 101-105, 151-153, 1 27-51-00Page 579 1201-207, 1May 01/05 1 1 1CES 1

 (b) The dimension S (the vertical measurement between the fixed shroud and the outboard end of the flap):
 1 Check the value shown on the label (42) attached to the
_ outboard side of the flap track 3 beam.
 2 If the value on the label (42) is '0', the dimension S must be
_
 zero +/- 1.5 mm (0.06 in.).

 3 If the value on the label (42) shows a plus value, subtract
_ the value from the dimension S. The remaining value must be zero +/- 1.5 mm (0.06 in.).
 4 If the value on the label (42) shows a minus value, add the
_ value to the dimension S. The remaining value must be zero +/-
1.5 mm (0.06 in.).
 (3) If the flap rigged position is not correct, adjust as necessary until
 the flap is in the specified limits (Ref. TASK 27-51-00-820-008). R

R **ON A/C 002-049, 053-061, 101-105, 201-203,
 Subtask 27-51-00-220-057-C
 C. To Do a Check of the Outboard Flap Rigged Position (Ref. Fig. 511/TASK 27-51-00-991-060, 512/TASK 27-51-00-991-058, 513/TASK 27-51-00-991-059)
 NOTE : The tolerances given in the work steps that follow are in-service
____ tolerances only. They are not initial adjustment tolerances. The tolerances for initial adjustment are given in the flap rigged position adjustment procedure (Ref. TASK 27-51-00-820-008).
 NOTE : The scale must be read from the outboard side of the flap track
____
 beam.

 (1) At the track 3 position, make sure that the top surface of the trailing edge aligns with the scale block (41) as follows:
 (a)
 Check the value shown on the label (42) attached to the outboard side of the flap track beam.

 (b)
 If the value on the label (42) is '0', make sure that the trailing edge aligns with the zero mark +/- 4 mm (0.16 in.).

R 1EFF : 001-049, 053-061, 101-105, 201-203, 1 27-51-00Page 580 1 1 May 01/05 1 1 1CES 1

 Label Position - Flap Track Beam
 Figure 511A/TASK 27-51-00-991-060-A

R 1EFF : 106-149, 154-199, 208-299, 401-499, 1 27-51-00Page 581 1 1 Aug 01/05 1 1 1CES 1
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱4(57)