A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Put the warning notice in position to tell persons not to pressurize the hydraulic systems.
(3)
Put a warning notice in position to tell persons not to operate the flight controls.
(4)
Put the adjustable access platform in position below the applicable flap.
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 27-54-00-860-062
B. Aircraft Maintenance Configuration WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
(1)
Extend the flaps to position 1 (Ref. TASK 27-50-00-866-008).
(2)
Remove the flap kink-seals (Ref. TASK 27-54-61-000-002).
(3)
Remove the applicable wing to fuselage panels (Ref. TASK 53-35-11-000-001):
-
for the LH flap, remove 193AB
-
for the RH flap, remove 194AB.
(4) Fully retract the flaps (Ref. TASK 27-50-00-866-009). **ON A/C 301-399,
Subtask 27-54-00-860-062-A
B. Aircraft Maintenance Configuration WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
(1)
Extend the flaps to position 1 (Ref. TASK 27-50-00-866-008).
(2)
Remove the flap kink-seals (Ref. TASK 27-54-61-000-002).
(3)
Disconnect the Z-Coupling:
(Ref. Fig. 607/TASK 27-54-00-991-017)
(a)
Remove and discard the cotter pin (1).
(b)
Remove the nut (2) and the washer (3).
(c)
Remove and discard the cotter pin (6).
(d)
Remove the nut (7), the washer (8) and the spacer(s) (9).
(e)
Retract the flaps fully (Ref. TASK 27-50-00-866-009).
(f)
Remove the bolt (10).
(g)
Remove the lever (4) and the remaining spacer(s) (9). NOTE : Record the position of the remaining spacer(s) (9) when
____ you remove them. This is to make sure the spacers are installed in the same position.
(h)
Temporarily install the spacer(s) (9), the washer (8) and the nut
(7)
on the lever (4).
(i)
Temporarily install the lever (4) on the attachment bracket (11) with the bolt (10), the washer (3) and the nut (2).
(j)
Turn the lever (4) forward as far as possible and hold it in this position with adhesive tape.
(k)
Turn the lever (5) forward as far as possible and hold it in this position with adhesive tape.
(4)
Remove the applicable wing to fuselage panels (Ref. TASK 53-35-11-000-001):
-
for the LH flap, remove 193AB
-
for the RH flap, remove 194AB.
(5)
Extend the flaps fully (Ref. TASK 27-50-00-866-008).
(6)
For the inboard flap:
Details of the Z-Coupling
R Figure 607/TASK 27-54-00-991-017
1EFF : 301-399, 1 27-54-00 Page 637
1 1 May 01/05
1 1
1CES 1
(a) Disconnect the upper tab-drive control-rod (22) from the shroud
box assembly attachment-bracket (26). R (Ref. Fig. 608/TASK 27-54-00-991-018)
1 Remove and discard the cotter pin (30).
_
2 Remove the nut (29), the washer (28) and the bolt (27).
_
3 Hold the tab drive control-rod (22) to the flap with adhesive
_
tape.
(b) Disconnect the tab drive control-rod (46) from the track 2
carriage (41). R (Ref. Fig. 609/TASK 27-54-00-991-019)
1 Remove and discard the cotter pin (44).
_
Details of the Hinge 1A Operating Mechanism R Figure 608/TASK 27-54-00-991-018
R 1EFF : 301-399, 1 27-54-00Page 639 1 1 May 01/05 1 1 1CES 1
Details of the Tab Drive Control-Rod (Track 2) R Figure 609/TASK 27-54-00-991-019
1EFF : 301-399, 1 27-54-00Page 640 1 1 May 01/05 1 1 1CES 1
R
R
R
2 Remove the nut (45), the washer (43), the bolt (47) and the
_
loose bush (42).
(c) Install the distance gages: 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱4(167)
