A. Put the aircraft back to its initial configuration.
(1) Make sure that the work area is clean and clear of tool(s) and other items.
TASK 27-51-43-000-002 Removal of the Lighted Plate WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-866-009 Retraction of the Flaps on the Ground 27-51-43-991-002 Fig. 402
3. Job Set-up
__________ Subtask 27-51-43-860-053
A. Aircraft Maintenance Configuration
(1)
Make sure that the flaps and slats are in the fully retracted position (Ref. TASK 27-50-00-866-009).
(2)
Make sure that the hydraulic systems are depressurized.
Subtask 27-51-43-865-053
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
-------------------------------------------------------------------------------
49VU FLIGHT CONTROLS/SLT FLP/POS/IND 1 1CN B12 R 49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 49VU FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1 5CV B06 121VU FLIGHT CONTROLS/WTB/FLP/SYS2 12CV P20 121VU FLIGHT CONTROLS/WTB/SLT/SYS2 11CV P19 121VU FLIGHT CONTROLS/SLT FLP/POS/IND2 2CN P16 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21 121VU FLIGHT CONTROLS/SLT/CTL/SYS2 7CV R21 122VU FLIGHT CONTROLS/WTB/FLP/SYS1 10CV S07 122VU FLIGHT CONTROLS/WTB/SLT/SYS1 9CV S06 122VU LIGHTING/INSTL LT/MAIN INST/PNL AND/PED 4LF Y04
4. Procedure
_________
(Ref. Fig. 402/TASK 27-51-43-991-002)
Subtask 27-51-43-020-052
A. Removal of the Lighted Plate
(1)
Remove the screw (13) and the handle (12).
(2)
Remove the set screw (14) and the pin (16).
(3)
Remove the index (15).
(4)
Remove the screws (11).
(5)
Remove the lighted plate (20).
Lighted Plate of the Flaps and Slats Control Lever
Figure 402/TASK 27-51-43-991-002
1EFF : ALL 1 27-51-43 Page 410
1 1 Feb 01/98
1 1
1CES 1
TASK 27-51-43-400-002 Installation of the Lighted Plate WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 08-007 USA MIL-R-46082 TYPE II SEALANT, HIGH TEMP. (Ref. 20-31-00)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-866-009 Retraction of the Flaps on the Ground 27-51-43-991-002 Fig. 402
3. Job Set-up
__________ Subtask 27-51-43-860-054
A. Aircraft Maintenance Configuration
(1)
Make sure that the flaps and slats are in the fully retracted position (Ref. TASK 27-50-00-866-009).
(2)
Make sure that the hydraulic systems are depressurized.
Subtask 27-51-43-865-054
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱4(104)
