(c)
Apply an up force (by hand) to the actuator lever. Apply sufficient force to make the actuator lever move through possible free movement in the flap system mechanism and joints.
(d)
Hold the actuator lever in this position, then measure and record the dimension S.
(e)
To find the total free movement (dimension X), subtract dimension S from dimension T.
(4)
Install the aluminum pin through the joint where you removed the bolt (141).
(5)
Retract the flaps fully (Ref. TASK 27-50-00-866-009).
(6)
Remove the aluminum pin.
R 1EFF : 301-399, 1 27-54-00Page 678 1 1 May 01/05 1 1 1CES 1
(7)
At the track 1 position, temporarily connect the flap drive arm to the rotary actuator drive-lever as follows:
(a)
Install the bolt (141), the washer (144) and the nut (145).
(b)
Hand tighten the nut (145).
(8)
At the track 2 position, disconnect the flap drive arm from the rotary actuator drive-lever:
(a)
Remove and discard the cotter pin (146).
(b)
Remove the nut (145) and the washer (144).
(c)
Remove the bolt (141) and install the aluminum pin (20.0 mm (0.7874 in.) diameter).
(d)
Extend the flaps fully (Ref. TASK 27-50-00-866-008).
(e)
Remove the aluminum pin.
(9)
At the inboard edge of the flap, measure the total free movement of the flap trailing edge:
(a)
Make sure that the flaps are fully extended, and that the travel ranges are clear.
(b)
Apply a down force (by hand) to the trailing edge of the flap. Apply sufficient force to make the flap move through possible free movement in the flap system mechanism and joints.
NOTE : Do not apply too much force to cause the system
____ components, mechanism or the aircraft fixed structure to move or bend.
(c)
Hold the flap in this position, then measure and record the dimension Z.
(d)
Apply an up force (by hand) to the trailing edge of the flap. Apply sufficient force to make the flap move through possible free movement in the flap system mechanism and joints.
NOTE : Do not apply too much force to cause the system
____ components, mechanism or the aircraft fixed structure to move or bend.
1EFF : 301-399, 1 27-54-00Page 679 1 1 May 01/05R 1 1 1CES 1
(e)
Hold the flap in position, measure and and record the dimension Y and then release the flap.
(f)
To find the total free movement, subtract the dimension Z from the dimension Y.
(10)
At the track 2 position, measure the total free movement of the actuator lever (dimension X):
(a)
Apply a down force (by hand) to the actuator lever. Apply sufficient force to make the actuator lever move through possible free movement in the flap system mechanism and joints.
(b)
Hold the actuator lever in this position, then measure and record the dimension T.
(c)
Apply an up force (by hand) to the actuator lever. Apply sufficient force to make the actuator lever move through possible free movement in the flap system mechanism and joints.
(d)
Hold the actuator lever in this position, then measure and record the dimension S.
(e)
To find the total free movement (dimension X), subtract dimension S from dimension T.
(11)
Install the aluminum pin through the joint where you removed the bolt (128).
(12)
Retract the flaps fully (Ref. TASK 27-50-00-866-009).
(13)
Remove the aluminum pin.
(14)
At the track 2 position, temporarily connect the flap drive arm to the rotary actuator drive-lever as follows:
(a)
Install the bolt (141), the washer (144) and the nut (145).
(b)
Hand tighten the nut (141).
(15)
Compare the measured free movement dimensions:
-the maximum acceptable value of free movement of the flap trailing edge at tracks 1 and 2 is 10.0 mm (0.3937 in.)
-for the maximum acceptable value of dimension X (free movement of the lever arm) refer to the table 601.
1EFF : 301-399, 1 27-54-00Page 680 1 1 May 01/05R 1 1 1CES 1
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 27-54-00-220-057
B. Detailed Dimensional Check - Free Movement at the Trailing Edge of the Outboard Flap
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱4(174)
