R 1EFF : 051-052, 1 27-51-00Page 589 1 1 May 01/05 1 1 1CES 1R **ON A/C 062-099, 106-149, 151-199, 204-299, 401-499,
Subtask 27-51-00-220-057-A
C. To Do a Check of the Outboard Flap Rigged Position
**ON A/C 062-099, 151-153, 204-207,
(Ref. Fig. 511/TASK 27-51-00-991-060) R **ON A/C 106-149, 154-199, 208-299, 401-499,
(Ref. Fig. 511A/TASK 27-51-00-991-060-A) R **ON A/C 062-099, 106-149, 151-199, 204-299, 401-499,
(Ref. Fig. 512A/TASK 27-51-00-991-058-A)
NOTE : The tolerances given in the work steps that follow are in-service
____ tolerances only. They are not initial adjustment tolerances. The tolerances for initial adjustment are given in the flap rigged position adjustment procedure (Ref. TASK 27-51-00-820-008).
NOTE : The scale must be read from the outboard side of the flap track
____
beam.
(1) At the track 3 and track 4 positions, make sure that the top surface of the trailing edge aligns with the scale block (41) as follows:
(a)
Check the value shown on the label (42) attached to the outboard side of the flap track 3 beam.
(b)
If the value on the label (42) is '0', make sure that the trailing edge aligns with the zero mark +/- 4 mm (0.16 in.).
(c)
If the value on the label (42) shows a plus value, subtract this value from the dimension shown on the scale block (41). The remaining value must be zero +/- 4 mm (0.16 in.).
(d)
If the value on the label (42) shows a minus value, add this value to the dimension shown on the scale block (41). The remaining value must be zero +/- 4 mm (0.16 in.).
R 1EFF : 062-099, 106-149, 151-199, 204-299, 1 27-51-00Page 590 1401-499, 1Aug 01/05 1 1 1CES 1
(2) If the flap rigged position is not correct, adjust as necessary until the flap is in the specified limits (Ref. TASK 27-51-00-820-008).
**ON A/C 301-399,
Subtask 27-51-00-220-057-D
C. To Do a Check of the Outboard Flap Rigged Position (Ref. Fig. 511B/TASK 27-51-00-991-060-B, 512B/TASK 27-51-00-991-058-B)
NOTE : The tolerances given in the work steps that follow are in-service
____ tolerances only. They are not initial adjustment tolerances. The tolerances for initial adjustment are given in the flap rigged position adjustment procedure (Ref. TASK 27-51-00-820-009).
NOTE : The scale must be read from the outboard side of the flap track
____
beam.
(1)
At the track 3 and track 4 positions, make sure that the top surface of the trailing edge aligns with the scale block (41) as follows:
(a)
Check the value shown on the label (42) attached to the outboard side of the flap track 3 beam.
(b)
If the value on the label (42) is '0', make sure that the trailing edge aligns with the zero mark +/- 4 mm (0.16 in.).
(c)
If the value on the label (42) shows a plus value, subtract this value from the dimension shown on the scale block (41). The remaining value must be zero +/- 4 mm (0.16 in.).
(d)
If the value on the label (42) shows a minus value, add this value to the dimension shown on the scale block (41). The remaining value must be zero +/- 4 mm (0.16 in.).
(2)
If the flap rigged position is not correct, adjust as necessary until the flap is in the specified limits (Ref. TASK 27-51-00-820-009).
R 1EFF : 062-099, 106-149, 151-199, 204-299, 1 27-51-00Page 591 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1
R **ON A/C 001-001,
R Subtask 27-51-00-080-050
R D. Removal of the Rigging Tools
R (1) Remove the KIT-FLAP RIGGING (98D27504038000):
R (Ref. Fig. 504/TASK 27-51-00-991-018)
R - for the inboard flap, from the flap track 2 beam assembly
R - for the outboard flap, from the flap track 3 beam assembly.
R (a) Remove the pin (12) and remove the fin (11) from the base
R assembly (15).
R (b) Hold the base assembly (15) and loosen the knurled screws (17).
R (c) Move the two lower clamps (16) clear of the flap track beam (18)
R and remove the base assembly (15).
R
R (Ref. Fig. 503/TASK 27-51-00-991-017)
R (2) Remove the PIN RIGGING-FLAPS (TRACK 1) (1) at the track 1 position.
R **ON A/C 002-049, 053-061, 101-105, 201-203,
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱4(59)
