Subtask 27-51-00-860-059
B. Aircraft Maintenance Configuration
(1)
Make sure that:
-the fuel quantities in the wing tanks are symmetrical or that the wing tanks are empty
-two engines are installed
or
-no engines are installed.
(2)
Make sure that the aircraft weight is:
- on the landing gear (weight on wheels)
or
- on jacks (Ref. TASK 07-11-00-581-001).
(3)
Make sure that the flaps are in the fully retracted position (Ref. TASK 27-50-00-866-009).
(4)
Make sure that the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER is on the flap/slat control lever.
**ON A/C 301-399,
Subtask 27-51-00-860-059-A
B. Aircraft Maintenance Configuration
(1)
Make sure that:
-the fuel quantities in the wing tanks are symmetrical or that the wing tanks are empty
-two engines are installed
or
-no engines are installed.
(2)
Make sure that the aircraft weight is on the landing gear (weight on wheels).
(3)
Make sure that the flaps are in the fully retracted position (Ref. TASK 27-50-00-866-009).
(4)
Make sure that the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER is on the flap/slat control lever.
**ON A/C ALL
Subtask 27-51-00-865-075
C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
**ON A/C 001-049, 053-061, 101-105, 201-203,
Subtask 27-51-00-010-055
D. Get Access
(1)
Open the applicable MLG door (Ref. TASK 32-12-00-010-001).
(2)
Make sure that the GROUND LOCK SLEEVE is on the applicable MLG door actuator.
(3)
Put the access platform(s) below the applicable inboard and outboard flaps.
(4)
Lower the flap track No. 2 movable fairing (Ref. TASK 57-55-11-010-001).
(5)
Lower the flap track No. 3 movable fairing (Ref. TASK 57-55-11-010-002).
R **ON A/C 051-052, 062-099, 106-149, 151-199, 204-299, 301-399, 401-499,
Subtask 27-51-00-010-055-A
D. Get Access
(1)
Open the applicable MLG door (Ref. TASK 32-12-00-010-001).
(2)
Make sure that the GROUND LOCK SLEEVE is on the applicable MLG door actuator.
(3)
Put the access platform(s) below the applicable inboard and outboard flaps.
(4)
Lower the flap track No. 2 movable fairing (Ref. TASK 57-55-11-010-001).
(5)
Lower the flap track No. 3 and the flap track No. 4 movable fairings (Ref. TASK 57-55-11-010-002).
**ON A/C ALL
4. Procedure
_________
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
_______
EDGE:
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
**ON A/C 001-001,
Subtask 27-51-00-480-051
A. Installation of the Rigging Tools
(Ref. Fig. 503/TASK 27-51-00-991-017, 504/TASK 27-51-00-991-018)
(1)
Install the PIN RIGGING-FLAPS (TRACK 1) (98D27504005000) (1) at the track 1 position only.
(2)
Install the KIT-FLAP RIGGING (98D27504038000):
-
for the inboard flap, on the flap track 2 beam assembly
-
for the outboard flap, on the flap track 3 beam assembly.
(a)
Install the base assembly (15) on the flap track beam (18). Make sure that the aft dowels (14) touch the track beam end-stop (13).
(b)
Move the two lower clamps (16) into position below the flap track beam (18) and tighten the knurled screws (17).
(c)
Move the fin (11) into position on the base assembly (15) and install the pin (12).
R 1EFF : ALL 1 27-51-00Page 557 1 1 May 01/04 1 1 1CES 1
Installation of the Flap Rigging Pin at Track 1
Figure 503/TASK 27-51-00-991-017
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 27-51-00Page 558 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1R Installation of the Flap Rigging Pin at Track 1 R Figure 503A/TASK 27-51-00-991-017-A 中國航空網 m.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱4(54)
