-
the clamp (7)
-
the pad (3)
-
the pivot clamp (1).
(2)
Loosen the screw (6).
(3)
Remove the pin (5) and the clamp (7).
(4)
Loosen the screw (9) sufficiently to let the clamp arm (8) move along the arm assembly (10).
(5)
Put the pivot clamp (1) in position on the flange of the wing structure.
(6)
Put the arm assembly (10) on the applicable torque shaft.
(7)
Put the clamp (7) on the torque shaft below the arm assembly (10) and install the pin (5). Do not tighten the screw (6) at this time.
(8)
Move the pivot clamp (1) together with the arm assembly (10) until the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT is in the correct position.
1EFF : ALL 1 27-50-00Page 250 1 1 May 01/04R 1 1 1CES 1
Lock-Torque Shaft (Flaps and Slats) Figure 205/TASK 27-50-00-991-004
1EFF : 1 1R 1CES ALL 1 11 1 27-50-00 Page 251 May 01/04
(9) Hold the pivot clamp (1) in position:
-
for the left wing, tighten the screw (2)
-
for the right wing, install the packer (4) and tighten the screw (2).
(10)
Tighten the screw (9).
(11)
Tighten the screw (6) until the clamp (7) and the arm assembly (10) lock the torque shaft in position.
5. Close-up
________ Subtask 27-50-00-942-059
A. Removal of Equipment
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the safety barriers.
(3)
Remove the warning notice(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 27-50-00Page 252 1 1 May 01/04R 1 1 1CES 1
TASK 27-50-00-000-003 Removal of the Lock-Torque Shaft - Flaps and Slats (98D27504030001) WARNING : MAKE SURE THAT THE FLIGHT CONTROL SAFETY-LOCKS AND THE WARNING
_______ NOTICES ARE IN POSITION.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers No specific warning notice
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-991-004 Fig. 205
3. Job Set-up
__________ Subtask 27-50-00-941-059
A. Safety Precautions
(1)
Make sure that the safety barriers are in position.
(2)
Make sure that the warning notice is in position on panel 114VU to tell persons not to operate the flap/slat control lever.
1EFF : ALL 1 27-50-00Page 253 1 1 May 01/04R 1 1 1CES 1
4. Procedure
_________ (Ref. Fig. 205/TASK 27-50-00-991-004) Subtask 27-50-00-080-050
A. Removal of the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT (98D27504030001)
(1)
Loosen the screw (6).
(2)
Remove the pin (5) and the clamp (7).
(3)
Loosen the screw (2). For the right wing, remove the packer (4).
(4)
Remove the pivot clamp (1) from the wing structure and the arm assembly (10) from the torque shaft.
(5)
Put the clamp (7) and the arm assembly (10) together and install the pin (5).
5. Close-up
________ Subtask 27-50-00-942-060
A. Removal of Equipment
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the safety barriers.
(3)
Remove the warning notice(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 27-50-00Page 254 1 1 May 01/04R 1 1 1CES 1
TASK 27-50-00-869-006
Reset of the Wing Tip Brake (WTB) of the Flap System on the Ground
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱4(4)
