(1)
Install the lighted plate (20) on the control lever assembly (19).
(2)
Install the screws (11) and tighten.
(3)
Install the index (15) on the lever (18).
(4)
Install the pin (16) through the levers (17) and (18).
(5)
Install the set screw (14) with BONDING AND ADHESIVE COMPOUNDS (Material No. 08-007) into the lever (17) and tighten.
(6)
Install the handle (12) on the lever (18).
(7)
Install the screw (13) with BONDING AND ADHESIVE COMPOUNDS (Material No. 08-007) and tighten.
Subtask 27-51-43-865-055
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 5CV, 6CV, 7CV, 8CV, 9CV, 10CV, 11CV, 12CV, 4LF, 1CN, 2CN
5. Close-up
________ Subtask 27-51-43-860-055
A. Put the aircraft back to its initial configuration.
(1) Make sure that the work area is clean and clear of tool(s) and other items.
STRUT - INTERCONNECTING - REMOVAL/INSTALLATION
______________________________________________
TASK 27-51-44-000-001
Removal of the Interconnecting Strut
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific blanking caps
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notice(s)
No specific access platform 3.5 m (11 ft. 6 in.)
98D27803000000 1 LOCKING TOOL - FLAP/SLAT CONTROL LEVER
1EFF : ALL 1 27-51-44Page 401 1 1 May 01/04R 1 1 1CES 1
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
27-00-00-480-002 Installation of the Flap/Slat Control-Lever Locking
Tool (98D27803000000)
27-50-00-866-008 Extension of the Flaps on the Ground
27-54-61-000-002 Removal of the Flap Kink-Seals
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
27-51-44-991-001 Fig. 401
**ON A/C 301-399,
27-51-44-991-001-A Fig. 401A
**ON A/C ALL
3. Job Set-up
__________ R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
(Ref. Fig. 401/TASK 27-51-44-991-001)
**ON A/C 301-399,
(Ref. Fig. 401A/TASK 27-51-44-991-001-A)
**ON A/C ALL
Subtask 27-51-44-941-059
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Put the warning notice(s) in position to tell persons not to operate the flap/slat controls.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱4(105)
