(b)
 Make sure the travel ranges are clear.

 (c)
 Apply a down force (by hand) to the trailing edge of the flap. Apply sufficient force to make the flap move through possible free movement in the flap system mechanism and joints.

 NOTE : Do not apply too much force to cause the system
____ components, mechanism or the aircraft fixed structure to move or bend.
 (d)
 Hold the flap in this position, measure and record the dimension Z and then release the flap.

 (e)
 Apply an up force (by hand) to the trailing edge of the flap. Apply sufficient force to make the flap move through possible free movement in the flap system mechanism and joints.

 NOTE : Do not apply too much force to cause the system
____ components, mechanism or the aircraft fixed structure to move or bend.
 (f)
 Hold the flap in this position, measure and record the dimension Y and then release the flap.

 (g)
 To find the total free movement, subtract the dimension Z from the dimension Y.

R 1EFF : 051-099, 103-149, 201-299, 1 27-54-00Page 673 1 1 May 01/05 1 1 1CES 1

 (3)
 At the track 1 position, measure the total free movement of the actuator lever (dimension X):

 (a)
 Apply a down force (by hand) to the actuator lever. Apply sufficient force to make the actuator lever move through possible free movement in the flap system mechanism and joints.

 (b)
 Hold the lever in this position, then measure and record the dimension T.

 (c)
 Apply an up force (by hand) to the actuator lever. Apply sufficient force to make the actuator lever move through possible free movement in the flap system mechanism and joints.

 (d)
 Hold the actuator lever in this position, then measure and record the dimension S.

 (e)
 To find the total free movement (dimension X), subtract the dimension S from the dimension T.

 (4)
 Install the aluminum pin through the joint where you removed the shearbolt (179).

 (5)
 Manually retract the flaps fully (Ref. TASK 27-50-00-866-012).

 (6)
 Remove the aluminum pin.

 (7)
 At the track 1 position, temporarily connect the flap drive arm to the rotary actuator drive-lever as follows:

 (a)
 Install the shearbolt (179), the washer (178) and the nut (177).

 (b)
 Hand tighten the nut (177).

 (c)
 Install the indicator pin (180), the indicator plate (181), the washers (182) and the bolts (183).

 (d)
 Hand tighten the bolts (183).

 (8)
 At the track 2 position, disconnect the flap drive arm from the rotary actuator lever-arm:

 (a)
 Remove and discard the cotter pin (187).

 (b)
 Remove the nut (186) and the washer (185).

R 1EFF : 051-099, 103-149, 201-299, 1 27-54-00Page 674 1 1 May 01/05 1 1 1CES 1

 (c)
 Remove the bolt (184) and install the aluminum pin (10.0 mm (0.3937 in.) diameter).

 (d)
 Extend the flaps manually (Ref. TASK 27-50-00-866-011) as follows:

 (e)
 Remove the aluminum pin.

 1_ Slowly extend the flaps until the dimension T at track 2 is
 approximately 6.0 mm (0.2362 in.).
 2_ Dimension T can be +/- 1.0 mm (0.0393 in.) but it must be set
 during the flap extension procedure. Do not retract the flaps
 in small amounts to set the dimension T.

 (9) At the inboard end of the flap, measure the total free movement of the flap trailing edge:
 (a)
 Refer to step 4.A.(8)(d) and make sure that the flaps are extended correctly.

 (b)
 Make sure the travel ranges are clear.

 (c)
 Apply a down force (by hand) to the trailing edge of the flap. Apply sufficient force to make the flap move through possible free movement in the flap system mechanism and joints.

 NOTE : Do not apply too much force to cause the system
____ components, mechanism or the aircraft fixed structure to move or bend.
 (d)
 Hold the flap in this position, measure and record the dimension Z and then release the flap.

 (e)
 Apply an up force (by hand) to the trailing edge of the flap. Apply sufficient force to make the flap move through possible free movement in the flap system mechanism and joints.

 NOTE : Do not apply too much force to cause the system
____ components, mechanism or the aircraft fixed structure to move or bend.
 (f)
 Hold the flap in this position, measure and record the dimension Y and then release the flap.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱4(172)