-at the outboard end of the flap, the dimension N (the vertical distance between the outer fixed shroud and the end of the flap) is zero +/- 1.0 mm (0.0393 in.).
R 1EFF : 001-049, 053-061, 101-105, 201-203, 1 27-51-00Page A539 1 1 Aug 01/05 1 1 1CES 1

 Rigging Dimensions - Outboard Flap
 Figure 522A/TASK 27-51-00-991-072-A

R 1EFF : 002-049, 053-061, 101-105, 201-203, 1 27-51-00Page A540 1 1 Aug 01/05 1 1 1CES 1 **ON A/C 051-052,

 Subtask 27-51-00-820-066-C
 D. Adjust the Rigged Position of the Outboard Flap
 (Ref. Fig. 520A/TASK 27-51-00-991-070-B, 521/TASK 27-51-00-991-071, 522B/TASK 27-51-00-991-072-B)
 NOTE : Label (42) shows the shark-fin calibration value at track 4.
____ Aircraft with this label used to have the outer fixed shroud as the datum point. The shark-fin uses the flap track beam as a datum. The shark-fin calibration value is the difference (distance) between the fixed shroud datum and the flap track beam datum. The value must be included when the position of the flap trailing edge is set.
 (1) Use the TOOL FLAP ADJUSTING to adjust the main eccentric bearings. Adjust the bearings at one track position then the other in small, equal increments. At the track 3 and the track 4 positions, adjust the main eccentric bearings until:
 (a) At the track 3 position, the flap top surface aligns:
 -with the zero line on the scale block (20), plus or minus 1.0 mm (0.0393 in.).
 NOTE : Look inboard from the outside of the flap track beam when
____
 you read the scale block.

 (b) At the track 4 position, the flap top surface aligns:
 -with the line on the scale block (20) which agrees with the calibration value on the track 4 label (42).
 NOTE : Look inboard from the outside of the flap track beam when
____
 you read the scale block.

R 1EFF : 051-052, 1 27-51-00Page A541 1 1 Aug 01/05 1 1 1CES 1

 Rigging Dimensions - Outboard Flap
 Figure 522B/TASK 27-51-00-991-072-B12 (SHEET 1)

R 1EFF : 051-052, 062-099, 106-149, 151-199, 1 27-51-00Page A542 1204-299, 401-499, 1Aug 01/05 1 1 1CES 1

 Rigging Dimensions - Outboard Flap
 Figure 522B/TASK 27-51-00-991-072-B22 (SHEET 2)

R 1EFF : 051-052, 062-099, 106-149, 151-199, 1 27-51-00Page A543 1204-299, 401-499, 1Aug 01/05 1 1 1CES 1R **ON A/C 062-099, 106-149, 151-199, 204-299, 401-499,

 Subtask 27-51-00-820-066-B
 D. Adjust the Rigged Position of the Outboard Flap (Ref. Fig. 521/TASK 27-51-00-991-071, 522B/TASK 27-51-00-991-072-B)
 (1) Use the TOOL FLAP ADJUSTING to adjust the main eccentric bearings. Adjust the bearings at one track position then the other in small, equal increments. At the track 3 and the track 4 positions, adjust the main eccentric bearings until at each position:
 -the top surface of the flap trailing edge aligns +/- 1.0 mm (0.0393 in.) with the zero line on the scale block (20).
 NOTE : Look inboard from the outside of the flap track beam when you
____
 read the scale block.

R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
 Subtask 27-51-00-420-073
 E. Remove the Adjusting Tools From the Main Eccentric Bearings of the Outboard Flap
 (Ref. Fig. 521/TASK 27-51-00-991-071)
 (1)
 Remove the TOOL - FLAP ADJUSTING, from the splined bush in the flap carriage at track 3 and track 4.

 (2)
 At the track 3 and track 4 positions do as follows:

 (a) On the carriage bolt (58) install these items:
 -the locking plate (51) (make sure that the main eccentric bearing, the splined bush and the locking plate (51) are correctly engaged)
 -a new crushable spacer (52)
 -the nut (53).
 (b)
 TORQUE the nut (53) to between 15 and 20 m.daN (110.61 and 147.49 lbf.ft).

 (c)
 Safety the nut (53) with a new cotter pin (54).

R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 27-51-00Page A544 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1

 (d)
 Install the washer (56) and the nut (55).

 (e)
 TORQUE the nuts (57) on the failsafe hooks to between 2.5 and 3.3 m.daN (18.43 and 24.33 lbf.ft).

 (f) Safety the nuts (57) with MISCELLANEOUS (Material No. 19-010). **ON A/C 001-001,
 Subtask 27-51-00-820-074
 F. Complete the Adjustment of the Rigged Position of the Outboard Flap
 (Ref. Fig. 518/TASK 27-51-00-991-068)

 (1)
 At the track 3 and the track 4 positions, complete the installation of:

 -the flap drive-arms (4) and the rotary actuator drive-levers (5) (Ref. TASK 27-54-62-400-001).

 (2)
 Connect the torque shaft universal-joints:
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱4(69)