-
a zero (0) value shows that no adjustment was necessary.
(e) If the value on the label (41) is zero (0), go to step (g).
R 1EFF : 001-001, 1 27-51-00Page A515 1 1 Aug 01/05 1 1 1CES 1
Rigging Pin Installation
Figure 518/TASK 27-51-00-991-068
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 27-51-00Page A516 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
INTENTIONALLY BLANK
R 1 1 27-51-00Page A517 1 1 Aug 01/05 1 1 1CES 1
Rigging Kit Installation - Outboard Flap Figure 519/TASK 27-51-00-991-069- 12 (SHEET 1)
R 1EFF : 001-001, 1 27-51-00Page A518 1 1 Aug 01/05 1 1 1CES 1
Rigging Kit Installation - Outboard Flap Figure 519/TASK 27-51-00-991-069- 22 (SHEET 2)
R 1EFF : 001-001, 1 27-51-00Page A519 1 1 Aug 01/05 1 1 1CES 1
Rigging Kit Installation - Outboard Flap
Figure 519A/TASK 27-51-00-991-069-B12 (SHEET 1)
R 1EFF : 002-049, 053-061, 101-105, 201-203, 1 27-51-00Page A520 1 1 Aug 01/05 1 1 1CES 1
Rigging Kit Installation - Outboard Flap
Figure 519A/TASK 27-51-00-991-069-B22 (SHEET 2)
R 1EFF : 002-049, 053-061, 101-105, 201-203, 1 27-51-00Page A521 1 1 Aug 01/05 1 1 1CES 1
Rigging Kit Installation - Outboard Flap
Figure 519B/TASK 27-51-00-991-069-A12 (SHEET 1)
R 1EFF : 051-052, 062-099, 106-149, 151-199, 1 27-51-00Page A522 1204-299, 401-499, 1Aug 01/05 1 1 1CES 1
Rigging Kit Installation - Outboard Flap
Figure 519B/TASK 27-51-00-991-069-A22 (SHEET 2)
R 1EFF : 051-052, 062-099, 106-149, 151-199, 1 27-51-00Page A523 1204-299, 401-499, 1Aug 01/05 1 1 1CES 1
Label Position - Flap Track 3
Figure 520/TASK 27-51-00-991-070
R 1EFF : 001-049, 053-099, 101-105, 151-153, 1 27-51-00Page A524 1201-207, 1Aug 01/05 1 1 1CES 1
(f)
If the label (41) shows a plus or minus value, adjust the forward eccentrics to the zero datum position (Ref. TASK 27-51-00-820-004).
(g)
Install the carriage restraint (30) between the base assembly
(23)
and the flap carriage (29). Make sure that the cut-out in the fork-end of the carriage restraint (30) is at the top. This will prevent damage to the greaser.
(h)
Adjust the carriage restraint (30) until it holds the flap carriage (29) in position.
(i)
Put the setting block (20) on the track 3 fin (21).
(3)
At the track 3 and track 4 positions:
(a) Disconnect the flap drive-arm (4) from the rotary actuator drive-lever (5) (Ref. TASK 27-54-62-000-001).
(4)
Carefully lower the flap until the trailing edge of the flap touches the setting block (20) on the track 3 fin (21).
(5)
Disconnect the torque shafts at the universal-joints:
(a)
At the two sides of the flap track 3 actuator (Ref. TASK 27-54-49-000-003).
(b)
At the inboard side of the flap track 4 actuator (Ref. TASK 27-54-49-000-004).
**ON A/C 002-049, 053-061, 101-105, 201-203,
Subtask 27-51-00-480-060-B
B. Install the Outboard Flap Rigging Kit
(Ref. Fig. 516A/TASK 27-51-00-991-067-A, 518/TASK 27-51-00-991-068, 519A/TASK 27-51-00-991-069-B)
(1)
Install the PIN RIGGING-FLAPS (TRACK 1) (98D27504005000) (1) at the track 1 position.
(2)
Install the PIN RIGGING FLAPS (98D27504006000) (7) at the track 2, 3 and 4 positions.
R 1EFF : 001-049, 053-061, 101-105, 201-203, 1 27-51-00Page A525 1 1 Aug 01/05 1 1 1CES 1
(3) At the track 3 position only, install the KIT-FLAP RIGGING (98D27504038001):
(a)
Install the base assembly (23) on the flap track beam (28). Make sure that the aft dowels (25) touch the track beam end-stop (24).
(b)
Move the two bottom clamps (26) into position below the flap track beam (28) and tighten the knurled screws (27).
(c)
Move the fin (21) into position in the slot on the base assembly
(23)
and install the pin (22).
(Ref. Fig. 520/TASK 27-51-00-991-070)
(d) Check the value shown on the label (41) attached to the outboard side of the flap track 3 beam assembly.
NOTE : Label (41) shows the assymetric offset value. This is the
____ adjustment applied to the forward eccentric bearing in the flap drive strut at tracks 3 and 4. The adjustment is necessary on some aircraft to give the correct aerodymamic balance:
-
a plus (+) value shows that the flap trailing edge was moved up
-
a minus (-) value shows that the flap trailing edge was moved down
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱4(66)
