曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

SUBTASK 27-51-56-860-002
(4) Use the primary system to retract the flaps to the UP position, do this task: Trailing Edge Flap
System Operation With Primary Control, TASK 27-51-00-860-801.
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-56
Page 406
Jun 10/2005
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SEAL RIB ANGLE GEARBOX - REMOVAL/INSTALLATION
1. General
A. This procedure has these tasks:
(1) A removal of the seal rib angle gearbox
(2) An installation of the seal rib angle gearbox.
B. The seal rib angle gearbox is installed between the seal ribs between the inboard and outboard flap.
TASK 27-51-57-000-801
2. Seal Rib Angle Gearbox Removal
(Figure 401)
A. References
Reference Title
27-51-00-040-801 Trailing Edge Flap System Deactivation (P/B 201)
B. Tools/Equipment
NOTE: When more than one tool part number is listed under the same "Reference" number, the
tools shown are alternates to each other within the same airplane series. Tool part numbers
that are replaced or non-procurable are preceded by "Opt:", which stands for Optional.
Reference Description
SPL-1726 Clamp Set - Trailing Edge Flap Torque Tube
(Part #: C27022-1, Supplier: 81205, A/P Effectivity: 737-600, -700,
-700C, -700ER, -700QC, -800, -900, -900ER, -BBJ)
C. Location Zones
Zone Area
561 Left Wing - Rear Spar to Trailing Edge, Outboard Of Inboard Flap,
Inboard of Fixed Trailing Edge
661 Right Wing - Rear Spar to Trailing Edge, Outboard of Inboard Flap,
Inboard of Fixed Trailing Edge
D. Access Panels
Number Name/Location
561AB Midspan Fixed Trailing Edge Access Panel - WBL 224
661AB Midspan Fixed T.E. Panel
E. Prepare for the Removal
SUBTASK 27-51-57-040-001
(1) Do this task: Trailing Edge Flap System Deactivation, TASK 27-51-00-040-801.
SUBTASK 27-51-57-010-001
(2) Below the seal rib angle gear assembly [5], do this task:
Remove this access panel:
Number Name/Location
561AB Midspan Fixed Trailing Edge Access Panel - WBL
224
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-57
Page 401
Oct 10/2006
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
or open this access panel:
Number Name/Location
661AB Midspan Fixed T.E. Panel
F. Seal Rib Angle Gearbox Removal
SUBTASK 27-51-57-020-001
(1) Disconnect the torque tubes [3] from the seal rib angle gear assembly [5]:
(a) Install clamp set, SPL-1726 on the torque tube [3] outboard of the seal rib angle gear
assembly [5].
(b) Remove the screws [4] that attach the coupling sleeves [1] to the splined couplings [2].
(c) Move the coupling sleeves [1] off the splined couplings [2].
SUBTASK 27-51-57-020-002
(2) Remove the seal rib angle gear assembly [5]:
(a) Remove the nuts [9], washers [8], washers [7] and bolts [6] that attach the seal rib angle
gear assembly [5] to the rib [10].
(b) Remove the seal rib angle gear assembly [5].
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-57
Page 402
Jun 10/2005
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Seal Rib Angle Gearbox Installation
Figure 401/27-51-57-990-801
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-57
Page 403
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
TASK 27-51-57-400-801
3. Seal Rib Angle Gearbox Installation
(Figure 401)
A. References
Reference Title
12-22-51-640-801 Trailing Edge Flap Torque Tube and Torque Tube Support
Lubrication (P/B 301)
27-51-00-440-801 Trailing Edge Flap System Reactivation (P/B 201)
27-51-00-820-802 Trailing Edge Flap Drive System Adjustment (P/B 501)
27-51-00-860-801 Trailing Edge Flap System Operation With Primary Control (P/B 201)
B. Tools/Equipment
NOTE: When more than one tool part number is listed under the same "Reference" number, the
tools shown are alternates to each other within the same airplane series. Tool part numbers
that are replaced or non-procurable are preceded by "Opt:", which stands for Optional.
Reference Description
SPL-1726 Clamp Set - Trailing Edge Flap Torque Tube
(Part #: C27022-1, Supplier: 81205, A/P Effectivity: 737-600, -700,
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 飛機(jī)維護(hù)手冊5 AIRCRAFT MAINTENANCE MANUA(88)