曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

2) Make sure the Dimension A on the bellcrank assembly [85] you will install is the same
as the bellcrank assembly [85] that you removed.
NOTE: The nominal dimension of the inboard bellcrank assembly [85] is 14.56 inches.
3) If the bellcrank assembly [85] is not the correct length, adjust the bellcrank
assembly [85]:
a) Loosen the nuts [123] on the adjustment fitting [122] until the locking washer [124] is
disengaged from the bellcrank assembly [85].
b) Change the position of the adjustment fitting [122].
c) Engage the locking washer [124] with the bellcrank assembly [85].
d) Tighten the nuts [123] on the adjustment fitting [122].
e) Install lockwire on the nuts [123].
(b) Apply grease, D00633 to the shank of the bolt [89].
NOTE: Make sure you do not get grease, D00633 on the threads of the bolt [89].
(c) Put the bellcrank assembly [85] in its position on the carriage assembly [71].
(d) Install the bolt [89] and washer [90] to attach the bellcrank assembly [85] to the carriage
assembly [71].
(e) Carefully clean all of the grease, D00633 from the threads of the bolt [89].
(f) Install the nut [92] and washer [91] on the bolt [89].
(g) Tighten the nut [92] to 240-410 pound-inches (27.2-46.3 newton-meters).
(h) Install the pin [93] in the nut [92].
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-23
Page 419
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(i) Attach the rubcap [86] to the bellcrank assembly [85] with the bolt [88], bolt [94], washers
[95] and nuts [96].
SUBTASK 27-51-23-420-013
(8) Connect the aft flap pushrod [94] to the aft flap [3]:
(a) Apply grease, D00633 to the shank of the bolt [77] and the inside of the bushing [79].
NOTE: Make sure you do not get grease, D00633 on the threads of the bolt [77].
(b) Install the bushing [79], bolt [77] and washer [78] to attach the aft flap pushrod [84] to the aft
flap [3].
NOTE: Make sure the head of the bolt [77] is inboard.
(c) Carefully clean all of the grease, D00633 from the threads of the bolt [77].
(d) Install the nut [81] and washer [80] on the bolt [77].
(e) Tighten the nut [81] to 65-100 pound-inches (7.4-11.2 newton-meters).
(f) Install the pin [82] in the nut [81].
G. Put the Airplane Back to Its Usual Condition
SUBTASK 27-51-23-420-014
(1) Do this task: Outboard Trailing Edge Flap Installation, TASK 27-51-21-400-801.
SUBTASK 27-51-23-440-002
(2) Do this task: Trailing Edge Flap System Reactivation, TASK 27-51-00-440-801.
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-23
Page 420
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
OUTBOARD FLAP CARRIAGES - INSPECTION/CHECK
1. General
A. This procedure contains the task to do an inspection of the carriages for the inboard trailing edge
flaps.
TASK 27-51-23-200-801
2. Outboard Flap Outboard Carriage Inspection
(Figure 601)
A. General
(1) This task gives wear limits for the outboard carriage on the outboard flap.
(2) This task is applicable to the carriages at flap supports No. 1 and 8.
B. References
Reference Title
27-51-23-000-801 Outboard Flap Outboard Carriage Removal (P/B 401)
27-51-23-400-801 Outboard Flap Outboard Carriage Installation (P/B 401)
C. Tools/Equipment
Reference Description
STD-1096 Micrometer - Depth, 0-1 Inch, Readable to 1/1000 Inch
STD-1097 Caliper - Vernier, 0-6 Inch, Readable to 1/1000 Inch
D. Location Zones
Zone Area
544 Left Wing - Fairing Flap Support No. 1
644 Right Wing - Fairing Flap Support No. 8
E. Procedure
SUBTASK 27-51-23-020-017
(1) Do this task: Outboard Flap Outboard Carriage Removal, TASK 27-51-23-000-801.
SUBTASK 27-51-23-020-018
(2) Use these tools to do a check for wear on the part of the outboard flap outboard carriage:
(a) micrometer (0-1 Inch, readable to 1/1000 Inch), STD-1096
(b) readable to 1/1000 inch vernier 0 - 6 inch caliper, STD-1097.
SUBTASK 27-51-23-020-019
(3) Examine the parts of the outboard flap outboard carriage (Table 601):
(a) Remove the parts that you will measure.
(b) Measure the parts with a micrometer (0-1 Inch, readable to 1/1000 Inch), STD-1096 or a
readable to 1/1000 inch vernier 0 - 6 inch caliper, STD-1097.
(c) Compare the dimensions you measured with the permitted wear dimensions.
(d) If the parts are not in tolerance, replace or repair the parts.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 飛機維護手冊5 AIRCRAFT MAINTENANCE MANUA(10)