曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

(4) Disconnect the electrical connector [38] from the flap skew sensor [35].
SUBTASK 27-59-01-020-004
(5) Remove the flap skew sensor [35]:
(a) Remove the bolt [34], washer [33] and washer [31] that attach the jumper wire [32] to the
flap skew sensor [35].
(b) Remove the bolts [36] and washers [37] that attach the flap skew sensor [35] to the sensor
input assembly [39].
(c) Remove the flap skew sensor [35] from the sensor input assembly [39].
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-59-01
Page 207
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Outboard Flap Inboard Skew Sensor Installation
Figure 202 (Sheet 1 of 2)/27-59-01-990-802
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-59-01
Page 208
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Outboard Flap Inboard Skew Sensor Installation
Figure 202 (Sheet 2 of 2)/27-59-01-990-802
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-59-01
Page 209
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
TASK 27-59-01-400-802
5. Outboard Flap Inboard Skew Sensor Installation
(Figure 202)
A. General
(1) This task is applicable to the flap skew sensors installed on flap supports No. 2 and 7.
B. References
Reference Title
27-51-00-440-801 Trailing Edge Flap System Reactivation (P/B 201)
27-51-00-860-804 Retract the Trailing Edge Flaps (P/B 201)
27-59-00-730-801 Flap Skew Detection System Functional Test (P/B 501)
SWPM 20-60-03 Standard Wiring Practices Manual
C. Consumable Materials
Reference Description Specification
A00247 Sealant - Pressure And Environmental - Chromate
Type
BMS5-95
A02315 Sealant - Low Density, Synthetic Rubber. 2 Part BMS5-142
C00913 Compound - Nondrying Resin Mix Corrosion
Inhibiting Material
BMS3-27
D00633 Grease - Aircraft General Purpose BMS3-33
G50171 Compound - Corrosion Inhibiting Compound,
Interior Application - D5026NS or ZC-026
D. Location Zones
Zone Area
543 Left Wing - Fairing Flap Support No. 2
643 Right Wing - Fairing Flap Support No. 7
E. Procedure
SUBTASK 27-59-01-860-008
(1) Make sure that these circuit breakers are open:
F/O Electrical System Panel, P6-2
Row Col Number Name
A 11 C01443 FC TE FLAP POS/SKEW SNSR & IND RIGHT
A 12 C00213 FC TE FLAP POS/SKEW SNSR & IND LEFT
SUBTASK 27-59-01-420-003
(2) Install the flap skew sensor [35]:
(a) Apply grease, D00633 to the packing [40].
(b) Install the packing [40] on the flap skew sensor [35].
(c) Apply grease, D00633 to the shaft of the flap skew sensor [35] and the splines on the sensor
input assembly [39].
(d) Apply a thin layer of compound, C00913 to the mating surface of the flap skew sensor [35]
and the sensor input assembly [39].
(e) Engage the shaft on the flap skew sensor [35] with the sensor input assembly [39].
NOTE: The shaft has a missing tooth on the splines.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-59-01
Page 210
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(f) Engage the alignment pin on the sensor input assembly [39] with the hole in the flap skew
sensor [35].
(g) Apply compound, C00913 to the shank and threads of the bolts [36].
(h) Install the bolts [36] and washers [37] to attach the flap skew sensor [35].
(i) Install the bolt [34], washer [33] and washer [31] to attach the jumper wire [32] to the flap
skew sensor [35].
(j) Make sure the bonding resistance between the flap skew sensor [35] and the jumper wire
[32] is less than 8 milliohms.
(k) Apply a bead of sealant, A02315 or sealant, A00247 to the head of the bolt [34].
SUBTASK 27-59-01-210-002
(3) Before you connect the electrical connector [38], examine the connector for corrosion.
WARNING: DO THE STEPS BELOW IF THE AIRPLANE OPERATES AT AIRPORTS WHERE
DEICING FLUID THAT CONTAIN POTASSIUM FORMATE IS USED. ALSO DO THE
STEPS FOR ALL AIRPLANES THAT YOU FOUND CORROSION IN THE
ELECTRICAL CONNECTORS IN THE MAIN WHEEL WELL. THE ELECTRICAL
CONNECTOR IS PART OF A SYSTEM THAT IS NECESSARY FOR SAFE FLIGHT.
(a) If there was corrosion, refer to (SWPM 20-60-03) to correct the problem.
(b) Apply the D5026NS or ZC-026 compound, G50171 to the connector (SWPM 20-60-03).
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 飛機維護手冊5 AIRCRAFT MAINTENANCE MANUA(131)