曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

F. Location Zones
Zone Area
543 Left Wing - Fairing Flap Support No. 2
643 Right Wing - Fairing Flap Support No. 7
G. Outboard Flap Inboard Track Installation
SUBTASK 27-51-25-420-007
(1) If it is not installed, install the transmission attach fitting assembly [42]:
(a) Put the transmission attach fitting assembly [42] in its location on the flap track [41].
(b) Install the bolts [65], washers [66] and nuts [67] that attach the aft end of the transmission
attach fitting assembly [42] to the flap track [41].
(c) Install the pins [68] in the nut [67].
SUBTASK 27-51-25-480-005
(2) If you will use the adapter, SPL-1733, install it on the flap track [41]:
(a) Install the adapter, SPL-1733 on the flap track [41] approximately 33 inches (84 cm) aft of the
track attach fitting.
(b) Put a low profile hydraulic jack, COM-1568 below the adapter, SPL-1733 to support the flap
track [41].
SUBTASK 27-51-25-420-008
(3) Install the flap track [41]:
(a) If it is not installed, install the shim [49] on the structure:
NOTE: Make sure the shim [49] is the same thickness as the shim [49] that you removed.
The original thickness of the shim [49] is on a marker on the structure.
1) Apply sealant, A00247 to the mating surface of the shim [49] and the structure.
2) Put the shim [49] in its position.
3) Apply a fillet seal of sealant, A00247 around the shim [49].
(b) Attach the aft end of the flap track [41] to the structure:
1) Lift the flap track [41] to its location on the structure.
2) Install the bolt [51], washer [50], washer [48] and nut [47] that attaches the inboard side
of the flap track [41] to the structure.
3) Install the bolt [43], washer [44], washer [45] and nut [46] that attaches the outboard
side of the flap track [41] to the structure.
(c) Attach the forward end of the flap track [41]:
1) Apply grease, D00633 to the outside of the fuse pin [61] and the inside of the bushings.
2) Install the fuse pin [61] that attaches the forward end of the flap track [41] to the track
attach fitting.
(d) Tighten the nut [47] to 1300-1800 pound-inches (146.9-203.3 newton-meters).
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-25
Page 417
Jun 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(e) Tighten the nut [46] to 870-1300 pound-inches (98.3-146.9 newton-meters).
(f) Make sure you can turn the fuse pin [61] in the joint with a maximum of 10 pound-inches
(1.1 newton-meters) torque.
NOTE: You can push up on the forward end of the flap track [41] to take the weight off the
fuse pin [61] when you measure the torque.
(g) Install the washer [62] and nut [63] on the fuse pin [61].
(h) Tighten the nut [63] to 330-350 pound-inches (37.3-39.5 newton-meters).
(i) Loosen the nut [63] to align the hole for the pin [64].
(j) Install the pin [64] in the nut [63].
SUBTASK 27-51-25-420-009
(4) Install the failsafe fitting assembly [60] on the track attach fitting:
(a) Put the failsafe fitting assembly [60] in its location on the track attach fitting.
(b) Install the bolts [59] and washers [58] to attach the failsafe fitting assembly [60].
SUBTASK 27-51-25-480-006
(5) If it is necessary, remove the adapter, SPL-1733 from the flap track [41].
SUBTASK 27-51-25-020-016
(6) Install the bolt [52], washer [53], washer [54], washer [55] and nut [56] to connect the jumper wire
[57] to the flap track [41].
SUBTASK 27-51-25-420-010
(7) Do this task: Outboard Flap Inboard Transmision Installation, TASK 27-51-41-400-802.
SUBTASK 27-51-25-420-011
(8) Do this task: Outboard Trailing Edge Flap Installation, TASK 27-51-21-400-801.
SUBTASK 27-51-25-420-012
(9) Do this task: Outboard Flap Inboard Skew Mechanism Installation, TASK 27-59-02-400-802.
SUBTASK 27-51-25-820-003
(10) Do this task: Outboard Trailing Edge Flap Adjustment, TASK 27-51-21-820-801.
SUBTASK 27-51-25-820-004
(11) Do this task: Flap Skew Detection System Adjustment, TASK 27-59-00-820-801.
SUBTASK 27-51-25-640-002
(12) Do this task: Outboard Flap Inboard Flap Track Lubrication, TASK 12-22-51-640-815.
H. Put the Airplane Back to Its Usual Condition
SUBTASK 27-51-25-410-002
(1) Install the fairings for the inboard track on the outboard flap:
(a) Do this task: Outboard Flap Inboard Support Aft Fairing Installation,
TASK 27-51-28-400-804.
(b) Do this task: Outboard Flap Inboard Support Forward Fairing Installation,
TASK 27-51-28-400-803.
SUBTASK 27-51-25-440-002
(2) Do this task: Trailing Edge Flap System Reactivation, TASK 27-51-00-440-801.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 飛機維護手冊5 AIRCRAFT MAINTENANCE MANUA(22)