曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

(e) At the inboard side of the outboard flap support, make sure that DIMENSION Y is 4.61
±0.10 inch (117.094 ±2.54 mm).
(f) At the outboard side of the outboard flap support, make sure that DIMENSION Y is 4.46
±0.10 inch (113.284 ±2.54 mm).
(g) At the outboard end of the aft flap, make sure that DIMENSION Y is 4.06 ±0.10 inch (103.124
±2.54 mm).
SUBTASK 27-51-22-820-005
(14) If the position of the seals [54] are not in the limits, adjust the position of the seals [54]:
(a) Remove the rig pins from the bellcranks [12].
(b) Extend the aft flap assembly [2], until you can get access to the fasteners for the seals [54].
To extend the flaps, do this task: Extend the Trailing Edge Flaps, TASK 27-51-00-860-803.
(c) Adjust the position of the applicable seal [54]:
1) Loosen the bolts [53] that attach the seal [54].
2) Move the seal [54] forward or aft.
3) Tighten the bolts [53].
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-22
Page 414
Oct 10/2005
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(d) Retract the aft flap assembly [2] until you can install the rig pins in the bellcranks [12]. To
retract the flap, do this task: Retract the Trailing Edge Flaps, TASK 27-51-00-860-804.
(e) Install the rig pins in the bellcranks [12].
(f) Make sure the distance between the seals [54] and the aft flap assembly [2] are in the limit.
G. Put the Airplane Back to Its Usual Condition
SUBTASK 27-51-22-440-001
(1) Do this task: Trailing Edge Flap System Reactivation, TASK 27-51-00-440-801.
SUBTASK 27-51-22-410-002
(2) Do this task: Outboard Flap Outboard Support Aft Fairing Installation, TASK 27-51-28-400-802.
SUBTASK 27-51-22-410-003
(3) Do this task: Outboard Flap Inboard Support Aft Fairing Installation, TASK 27-51-28-400-804.
SUBTASK 27-51-22-860-002
(4) Retract the trailing edge flaps to the retracted position. To retract the flaps, do this task: Retract
the Trailing Edge Flaps, TASK 27-51-00-860-804.
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-22
Page 415
Oct 10/2005
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Outboard Aft Flap Adjustment
Figure 402 (Sheet 1 of 4)/27-51-22-990-802
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-22
Page 416
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Outboard Aft Flap Adjustment
Figure 402 (Sheet 2 of 4)/27-51-22-990-802
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-22
Page 417
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Outboard Aft Flap Adjustment
Figure 402 (Sheet 3 of 4)/27-51-22-990-802
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-22
Page 418
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Outboard Aft Flap Adjustment
Figure 402 (Sheet 4 of 4)/27-51-22-990-802
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-22
Page 419
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
OUTBOARD AFT FLAP - INSPECTION/CHECK
1. General
A. This procedure contains a task to do an inspection of the attachment points for the outboard aft flap.
The attachment points are the aft flap drive rods and the aft flap tracks.
TASK 27-51-22-200-801
2. Outboard Aft Flap Inspection
(Figure 601)
A. References
Reference Title
27-51-22-000-801 Outboard Aft Flap Removal (P/B 401)
27-51-22-400-801 Outboard Aft Flap Installation (P/B 401)
B. Tools/Equipment
Reference Description
STD-1096 Micrometer - Depth, 0-1 Inch, Readable to 1/1000 Inch
STD-1097 Caliper - Vernier, 0-6 Inch, Readable to 1/1000 Inch
C. Location Zones
Zone Area
567 Left Wing - Outboard Flap
667 Right Wing - Outboard Flap
D. Procedure
SUBTASK 27-51-22-020-003
(1) Do this task: Outboard Aft Flap Removal, TASK 27-51-22-000-801.
SUBTASK 27-51-22-020-004
(2) Use these tools to do a check for wear on the part of the outboard aft flap:
(a) micrometer (0-1 Inch, readable to 1/1000 Inch), STD-1096
(b) readable to 1/1000 inch vernier 0 - 6 inch caliper, STD-1097.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 飛機維護手冊5 AIRCRAFT MAINTENANCE MANUA(2)