曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

27-51-28-400-804 Outboard Flap Inboard Support Aft Fairing Installation (P/B 401)
29-11-00-860-801 Hydraulic System A or B Pressurization (P/B 201)
29-11-00-860-805 Hydraulic System A or B Power Removal (P/B 201)
C. Consumable Materials
Reference Description Specification
D00633 Grease - Aircraft General Purpose BMS3-33
D. Expendables/Parts
AMM Item Description AIPC Reference AIPC Effectivity
42 Ballscrew assembly 27-51-42-02-025 GUN 001-007, 106-108,
155-157, 201-999
50 Collar 27-51-42-02-020 GUN 001-007, 106-108,
155-157, 201-999
51 Washer 27-51-42-02-015 GUN 001-007, 106-108,
155-157, 201-999
52 Bolt 27-51-42-02-010 GUN 001-007, 106-108,
155-157, 201-999
54 Gimbal 27-51-42-02-050 GUN 001-007, 106-108,
155-157, 201-999
E. Location Zones
Zone Area
543 Left Wing - Fairing Flap Support No. 2
567 Left Wing - Outboard Flap
643 Right Wing - Fairing Flap Support No. 7
667 Right Wing - Outboard Flap
F. Outboard Flap Inboard Ballscrew and Gimbal Installation
SUBTASK 27-51-42-420-004
(1) If you removed it, install the gimbal [54] on the ballscrew nut [53]:
(a)
Apply grease, D00633 to the inside and outside mating surfaces of the gimbal bushings
[45].
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-42
Page 415
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
GUN 001-099, 101-122, 156, 157, 201-999; GUN 155 POST 737-SL-57-077
(b) Apply grease, D00633 to the outside surfaces of the gimbal bushings [45].
GUN ALL
(c) Put the gimbal [54] in its location on the ballscrew nut [53].
(d) Install the gimbal bushings [45] through the gimbal [54] on the ballscrew nut [53].
(e) Install the bolts [52], washers [51] and collars [50] to attach the gimbal bushings [45] to the
gimbal [54].
SUBTASK 27-51-42-420-005
(2) Connect the ballscrew assembly [42] to the yoke [44] on the transmission [43]:
(a) Turn the ballscrew nut [53] until it is at the forward end of the ballscrew assembly [42].
(b) Apply a layer of grease, D00633 to the mating surfaces of the yoke [44] and the ballscrew
assembly [42].
(c) Put the ballscrew assembly [42] into the yoke [44].
(d) Apply a layer of grease, D00633 to the shank and threads of the bolts [56].
(e) Install the bolts [56], washers [57], washers [58] and nuts [59] to attach the ballscrew
assembly [42] to the yoke [44].
(f) Make sure the ballscrew assembly [42] is installed correctly in the yoke [44]:
1) Turn the transmission [43] until the nut [61] on the U-joint [60] is down.
2) Turn the ballscrew nut [53] until the upstop is 1808 from the upstop [62] on the yoke [44].
3) If the ball returns on the ballscrew nut [53] are not on the outboard side, change the
position of the ballscrew assembly [42]:
a) Remove the nuts [59], washers [58], washers [57] and bolts [56] that attach the
ballscrew assembly [42] to the yoke [44].
b) Turn the ballscrew assembly [42] 1808 in the yoke [44].
c) Install the bolts [56], washers [57], washers [58] and nuts [59].
(g) Tighten the nuts [59].
SUBTASK 27-51-42-420-006
(3) Connect the ballscrew assembly [42] with the gimbal [54] to the carriage [41]:
(a) Move the gimbal [54] aft on the ballscrew assembly [42] until it is at the downstop.
(b) On transmission No. 2, make sure the ball returns on the ballscrew nut [53] are on the
outboard side.
(c) On transmission No. 7, make sure the ball returns on the ballscrew nut [53] are on the
inboard side.
GUN 155 PRE SB 737-57-1264
(d) Apply grease, D00633 to the inside and outside surfaces of the carriage bushing [49] and
carriage bushing [55].
GUN 001-099, 101-122, 156, 157, 201-999; GUN 155 POST SB 737-57-1264
(e) Apply grease, D00633 to the outside surfaces of the carriage bushing [49] and carriage
bushing [55].
GUN ALL
(f) Lift the outboard flap until the carriage [41] aligns with the gimbal [54].
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-42
Page 416
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(g) Install the carriage bushing [49] and carriage bushing [55] to attach the gimbal [54] to the
carriage [41].
(h) Install the bolts [46], washers [47] and nuts [48] to hold the carriage bushing [49] and
carriage bushing [55] in the carriage [41].
(i) Tighten the nuts [48] to 65-75 pound-inches (7.4-8.4 newton-meters) more than the run on
torque.
SUBTASK 27-51-42-640-002
(4) Lubricate the transmission [43], ballscrew assembly [42] and gimbal [54]. To lubricate them, do
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 飛機維護手冊5 AIRCRAFT MAINTENANCE MANUA(68)