曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

[7]:
(a) Put the upper side cover [1] and the lower side cover [3] in their position on the control
stand [7].
NOTE: The lower side cover [3] goes under the upper side cover [1].
(b) Install the screws [8] that attach the upper side cover [1] and lower side cover [3] to the
control stand [7].
(c) Install the pocket assembly [6] with the screws [5] on the lower side cover [3].
SUBTASK 27-51-06-410-006
(2) Install the stabilizer trim wheel [41] on the right side of the control stand [7]:
(a) Put the stabilizer trim wheel [41] on the shaft.
NOTE: Make sure the handle on the stabilizer trim wheel is 75 to 105 degrees from the
handle on the left stabilizer trim wheel.
(b) Install the bolt [42] to attach the stabilizer trim wheel [41].
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-06
Page 214
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Flap Control Lever Position Sensor Inspection
Figure 203 (Sheet 1 of 2)/27-51-06-990-803
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-06
Page 215
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Flap Control Lever Position Sensor Inspection
Figure 203 (Sheet 2 of 2)/27-51-06-990-803
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-06
Page 216
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
FLAP LEVER POSITION SWITCHES - REMOVAL/INSTALLATION
1. General
A. This procedure has these tasks:
(1) A removal of the flap lever position switches
(2) An installation of the flap lever position switches.
B. There are two flap lever position switches installed on the control stand.
(1) The flap lever 30-unit position switch
(2) the flap lever UP position switch
C. The flap lever position switches are installed on the control stand and operate with the flap control
lever.
D. There are two options for removal and installation of the flap lever position switches:
(1) You can remove and install the two flap lever position switches as an assembly.
(2) You can remove and install the two flap lever position switches independently by cutting and
splicing the wires.
TASK 27-51-08-000-801
2. Flap Lever Position Switch Removal
(Figure 401)
A. Location Zones
Zone Area
212 Flight Compartment - Right
B. Access Panels
Number Name/Location
112A Forward Access Door
C. Prepare for the Removal
SUBTASK 27-51-08-860-001
(1) Open these circuit breakers and install safety tags:
F/O Electrical System Panel, P6-2
Row Col Number Name
A 6 C00566 FLIGHT CONTROL FLAP LOAD RELIEF
A 7 C00210 FLIGHT CONTROL FLAP SHUTOFF VALVES
F/O Electrical System Panel, P6-3
Row Col Number Name
C 10 C00284 PANEL & INSTR ELEX PANEL
SUBTASK 27-51-08-010-001
(2) Remove the stabilizer trim wheel [8] from the right side of the control stand [13]:
(a) Remove the bolt [9] that attaches the stabilizer trim wheel [8].
(b) Remove the stabilizer trim wheel [8] from the shaft.
SUBTASK 27-51-08-010-002
(3) Remove the upper side cover [7] and lower side cover [11] from the right side of the control
stand [13]:
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-08
Page 401
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(a) Remove the screws [10] and the pocket assembly [12] from the lower side cover [11].
(b) Remove the screws [6] that attach the upper side cover [7] and the lower side cover [11] to
the control stand [13].
(c) Remove the upper side cover [7] and the lower side cover [11] from the control stand [13].
SUBTASK 27-51-08-010-003
(4) Remove the stabilizer trim lightplate [3] from the control stand [13]:
(a) Remove the screws [4] and remove the stabilizer trim lightplate [3].
(b) Remove the nuts [17], washers [16] and washers [15] that attach the wires [14] to the
stabilizer trim lightplate [3].
SUBTASK 27-51-08-010-004
(5) Remove the screws [2] and bolt [5] and remove the control stand cover [1] from the control stand
[13].
D. Flap Lever Position Switch Removal
SUBTASK 27-51-08-020-001
(1) Disconnect the electrical connector [28] for the flap lever position switches [24]:
(a) To get access to the electrical connector [28] from below the control stand [13], do this task.
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 AIRCRAFT MAINTENANCE MANUAL飛機維護手冊4(78)