曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

the carriage [13].
2) On the left wing, make sure the ball returns [25] on the ballscrew nuts [26] are
outboard.
3) On the right wing, make sure the ball returns [25] on the ballscrew nuts [26] are
inboard.
NOTE: This is the preferred position for maintenance.
GUN 155 PRE SB 737-57-1264; AIRPLANES WITH LUBRICATION FITTINGS ON THE CARRIAGE AND
GIMBAL BUSHINGS
(f) Apply grease, D00633 to the inside and outside surfaces of the carriage bushing [21] and
carriage bushing [27].
1) Install the carriage bushing [21] and carriage bushing [27] to attach the gimbal [20] to
the carriage [13].
CAUTION: MAKE SURE THE CARRIAGE BUSHINGS ALIGN WITH THE CARRIAGE
BEFORE YOU INSTALL THE BOLTS. THE THREADS ON THE BOLTS CAN
CAUSE DAMAGE TO THE CARRIAGE BUSHINGS IF THEY DO NOT
ALIGN.
2) Turn the carriage bushing [21] and carriage bushing [27] in the carriage [13] to make
sure the groove aligns with the bolt hole.
3) Install the bolts [22], washers [23] and nuts [24] to hold the carriage bushing [21] and
carriage bushing [27] in the carriage [13].
4) Tighten the nuts [24] to 65-75 pound-inches (6.8-8.4 newton-meters) more than the runon
torque.
GUN ALL
SUBTASK 27-51-21-420-002
(2) Install the stop fittings on the flap tracks:
(a) On the outboard track [41], install the roller stop [32], roller stop [42] and fairing attach
fitting [36]:
1) Apply compound, C00913 to the mating surfaces of the fairing attach fitting [36], roller
stop [32] and roller stop [42].
2) Put the roller stop [32], roller stop [42] and fairing attach fitting [36] in their positions on
the outboard track [41].
NOTE: Make sure the roller stop [32] and roller stop [42] touch the web of the
outboard track [41].
3) Apply compound, C00913 to the shank and threads of the bolts [33] and bolts [37].
4) Install the bolts [37], washers [38], washers [39] and nuts [40] that attach the roller stop
[32], roller stop [42] and fairing attach fitting [36] to the outboard track [41].
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-21
Page 415
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
5) Install the bolts [33], washers [34] and nuts [35] that attach the fairing attach fitting [36]
to the outboard track [41].
NOTE: Install the washers [34] with the countersunk outside diameter against the
outboard track [41].
(b) On the inboard track [53], install the roller stop [46], roller stop [54] and fairing attach fitting
[51]:
1) Apply compound, C00913 to the mating surfaces of the fairing attach fitting [51], roller
stop [46] and roller stop [54].
2) Put the roller stop [46], roller stop [54] and fairing attach fitting [51] in their positions on
the inboard track [53].
NOTE: Make sure the roller stop [46] and roller stop [54] touch the web of the inboard
track [53].
3) Apply compound, C00913 to the shank and threads of the bolts [47], bolts [52] and bolt
[43].
4) Install the bolts [47], washers [48], washers [49] and nuts [50] that attach the roller stop
[46], roller stop [54] and fairing attach fitting [51] to the inboard track [53].
5) Install the bolts [52], bolt [43], washers [44] and nuts [45] that attach the fairing attach
fitting [51] to the inboard track [53].
NOTE: Install the washers [44] with the countersunk outside diameter against the
inboard track [53].
SUBTASK 27-51-21-080-001
(3) Remove the sling, SPL-1729 from the main flap assembly [1] (Figure 402):
(a) Disconnect the sling, SPL-1729 [72] from the 30 foot height (2000 lbs capacity) lift crane,
STD-1095.
(b) Disconnect the sling, SPL-1729 [72] from the sling fittings [71].
(c) Remove the sling fittings [71] from the main flap assembly [1].
(d) Apply compound, C00528 to the holes for the bolts [74] and bolts [75] in the main flap
assembly [1].
(e) Install the bolts [74] at the inboard and outboard ends of the main flap assembly [1].
(f) Install the bolts [75] at the front spar of the main flap assembly [1].
SUBTASK 27-51-21-410-005
(4) Install the leading edge skin panel [55] on the main flap assembly [1] forward of the inboard
carriage [12]:
(a) These panels are:
Number Name/Location
567BT Flap, Forward Carriage Bearing And Fitting
667BT Flap, Forward Carriage Bearing And Fitting
(b) Put the leading edge skin panel [55] in its location on the leading edge of the main flap
assembly [1].
(c) Apply compound, C00528 to the holes for the bolts [56].
(d) Install the bolts [56] to attach the leading edge skin panel [55].
(e) Apply sealant, A00247 to fill all of the clearances around the leading edge skin panel [55]
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 AIRCRAFT MAINTENANCE MANUAL飛機維護手冊4(133)