曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

the flap control valve [19]. If the flaps retracted too far, adjust the valve slide [29]
to be further in the flap control valve [19].
(c) Tighten the nut [30] and nut [32] on the adjustable sleeve [31].
NOTE: Make sure the distance between the center of the rod end [24] and the nut [32] is
less than 0.94 inch (23.9 millimeters). Make sure the distance between the nut [30]
and the hex on the adjustable sleeve [31] is less than 0.19 inch (4.8 millimeters).
CAUTION: MAKE SURE HYDRAULIC POWER IS REMOVED BEFORE YOU DISCONNECT THE
ROD END FROM THE SUMMING LEVER. IF YOU DISCONNECT THE ROD END
WITH HYDRAULIC POWER ON YOU CAN CAUSE DAMAGE TO THE FLAP
CONTROL UNIT.
(d) If it is necessary, disconnect the rod end [24] from the summing lever [20]:
NOTE: It is necessary to disconnect the rod end [24] if you cannot adjust the valve slide
[29] enough to get the flaps in the correct position.
1) Remove the nut [23], washer [22] and bolt [21] that attach the rod end [24] to the
summing lever [20].
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-00
Page 518
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
2) Change the position of the adjustable sleeve [31].
3) Install the bolt [21], washer [22] and nut [23] to attach the rod end [24] to the summing
lever [20].
(e) Tighten the nut [30] and nut [32].
WARNING: KEEP PERSONS AND EQUIPMENT CLEAR OF THE FLIGHT CONTROL SURFACES,
THE THRUST REVERSERS, AND THE LANDING GEAR. THESE COMPONENTS
CAN MOVE SUDDENLY WHEN YOU SUPPLY HYDRAULIC POWER. THIS CAN
CAUSE INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
(f) Supply system B hydraulic power, do this task: Hydraulic System A or B Pressurization,
TASK 29-11-00-860-801.
(g) Use the primary system to fully extend and retract the trailing edge flaps a minimum of five
times. To extend and retract the flaps, do this task: Trailing Edge Flap System Operation
With Primary Control, TASK 27-51-00-860-801.
(h) Remove system B hydraulic power, do this task: Hydraulic System A or B Power
Removal, TASK 29-11-00-860-805.
(i) Make sure you can install the rig pin [27] in the flap control unit [4].
(j) Make sure the ballscrew nuts for transmission No. 4 and No. 5 are 1/2 turn ±10 degrees
(±0.25 inch) (±6.3 millimeters) from the upstop on the ballscrew yoke.
SUBTASK 27-51-00-420-003
(18) Install lockwire on the nut [30], nut [32] and the adjustable sleeve [31].
J. Put the Airplane Back to Its Usual Condition
SUBTASK 27-51-00-410-002
(1) Close this access panel:
Number Name/Location
112A Forward Access Door
or install this access panel:
Number Name/Location
114AC Fwd Nose Wheel Well Upper Access Panel
SUBTASK 27-51-00-410-003
(2) Install the floor panel above the flap control unit [4], do this task: Passenger Cabin Floor Panel
Installation, TASK 53-21-00-400-801.
SUBTASK 27-51-00-410-004
(3) Install the lower pan [26] on the flap control unit [4]:
(a) Put the lower pan [26] in its location on the flap control unit [4].
(b) Apply compound, C00913 to the shank and threads of the screws [25].
(c) Install the washers [32] and screws [25] to attach the lower pan [4].
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-00
Page 519
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Trailing Edge Flap Control System Adjustment
Figure 502 (Sheet 1 of 8)/27-51-00-990-805
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-00
Page 520
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Trailing Edge Flap Control System Adjustment
Figure 502 (Sheet 2 of 8)/27-51-00-990-805
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-00
Page 521
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Trailing Edge Flap Control System Adjustment
Figure 502 (Sheet 3 of 8)/27-51-00-990-805
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-00
Page 522
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Trailing Edge Flap Control System Adjustment
Figure 502 (Sheet 4 of 8)/27-51-00-990-805
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-00
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 AIRCRAFT MAINTENANCE MANUAL飛機維護手冊4(47)