曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-13
Page 410
Oct 10/2003
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
TASK 27-51-13-400-802
5. Inboard Flap Inboard Carriage Installation
(Figure 402)
A. General
(1) This task is applicable to the flap carriages at flap supports No. 4 and 5.
B. References
Reference Title
27-51-00-440-801 Trailing Edge Flap System Reactivation (P/B 201)
27-51-11-400-801 Inboard Trailing Edge Flap Installation (P/B 401)
C. Consumable Materials
Reference Description Specification
A00247 Sealant - Pressure And Environmental - Chromate
Type
BMS5-95
C00528 Compound - Corrosion Preventive, Petroleum Hot
Application (Soft Film)
MIL-C-11796,
Class III
D. Expendables/Parts
AMM Item Description AIPC Reference AIPC Effectivity
34 Carriage assembly 27-51-13-02-010 GUN 001-014, 101-108,
155-157, 201-999
27-51-13-02-015 GUN 001-014, 101-108,
155-157, 201-999
40 Torque tube 27-51-58-02-160 GUN 001-028, 101-121,
155-157, 201-999
E. Location Zones
Zone Area
541 Left Wing - Fairing Flap Support No. 4
553 Left Wing - Inboard Flap
641 Right Wing - Fairing Flap Support No. 5
653 Right Wing - Inboard Flap
F. Inboard Flap Inboard Carriage Installation
SUBTASK 27-51-13-420-003
(1) Install the carriage assembly [34] on the main flap [1]:
(a) Put the carriage assembly [34] in its position on the primary torque tube [38].
(b) Apply sealant, A00247 to the mating surface of the spacers [52].
(c) Apply sealant, A00247 to the shank and threads of the bolts [47] and bolt [54].
(d) Install the bolts [47] and bolt [54] with the spacers [52] through the primary torque tube [38]
and the carriage assembly [34].
(e) Put the attach plate [37] and rub block [33] in their position on the bolts [47].
(f) Install the washers [45] and nuts [46] on the bolts [47] and bolt [54].
(g) If they are not installed, install the bolts [35] and washers [36] that attach the rub block [33]
to the attach plate [37].
SUBTASK 27-51-13-420-004
(2) Install the secondary torque tube [40] in the main flap [1]:
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-13
Page 411
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
(a) Put the secondary torque tube [40] in its location in the primary torque tube [38].
(b) Install the bolts [50] and washers [51] through the secondary torque tube [40], primary
torque tube [38] and the carriage assembly [34].
(c) Apply sealant, A00247 to the filler [53].
(d) Install the filler [53], washers [48] and nuts [49] on the bolts [50].
NOTE: Install the filler [53] on the bottom bolt [50].
(e) Install the retainer [39] on the secondary torque tube [40].
1) Turn the retainer [39] until the holes for the bolts [41] align.
2) Apply sealant, A00247 to the fillers [43].
3) Install the bolts [41], washers [42], fillers [43] and nuts [44].
SUBTASK 27-51-13-410-002
(3) Install the upper skin panel [31] on the main flap [1]:
(a) Apply sealant, A00247 to the mating surface of the upper skin panel [31] and the main flap
[1].
(b) Put the upper skin panel [31] in its position.
(c) Install the bolts [32]:
1) Apply compound, C00528 to the forward and aft rows of holes in the upper skin panel
[31].
2) Install the bolts [32] in the forward and aft rows of holes.
3) Apply sealant, A00247 to the bolts [32] that go in the ribs and stiffeners in the main flap
[1].
4) Install the bolts [32] in the ribs and stiffeners.
G. Put the Airplane Back to Its Usual Condition
SUBTASK 27-51-13-420-005
(1) Do this task: Inboard Trailing Edge Flap Installation, TASK 27-51-11-400-801.
SUBTASK 27-51-13-440-002
(2) Do this task: Trailing Edge Flap System Reactivation, TASK 27-51-00-440-801.
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-51-13
Page 412
Oct 10/2005
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
INBOARD FLAP CARRIAGES - INSPECTION/CHECK
1. General
A. This procedure contains the task to do an inspection of the carriages for the inboard trailing edge
flaps.
TASK 27-51-13-200-801
2. Inboard Flap Outboard Carriage Inspection
(Figure 601)
A. General
(1) This task gives wear limits for the outboard carriage on the inboard flap.
(2) This task is applicable to the carriages at flap supports No. 3 and 6.
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 AIRCRAFT MAINTENANCE MANUAL飛機維護手冊4(106)