曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

1) Move the stabilizer until the limit switch [1] does not touch the cam.
2) Adjust the limit switch arm [3].
CAUTION: DO NOT MOVE THE SWITCH ARM [3] BEYOND ITS RANGE OF MOTION.
IT CAN CAUSE DAMAGE TO THE LIMIT SWITCH [1].
3) Move the stabilizer by hand until the limit switch [1] clicks.
4) Make sure the "B" dimension is the same as follows:
a) With the stabilizer autopilot and electric actuator nose down (flaps not up), make
sure the switch S145 "B" dimension at 0.05 units of trim is 45.48 ±0.05 in.
(1155.2 ±1.3 mm).
GUN 101-122
b) With the stabilizer electric actuator nose down (flaps up), make sure the switch
S844 "B" dimension at 4.30 units of trim is 39.46 ±0.05 in. (1002.3 ±1.3 mm).
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-41-94
Page 502
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
GUN 101-122 (Continued)
GUN 001-099, 155-157, 201-999
c) With the stabilizer electric actuator nose down (flaps up), make sure the switch
S844 "B" dimension at 3.95 units of trim is 39.96 ±0.05 in. (1015.0 ±1.3 mm).
GUN ALL
d) With the stabilizer autopilot and electric actuator nose up, make sure the switch
S144 "B" dimension at 14.50 units of trim is 24.80 ±0.05 in. (629.9 ±1.3 mm).
(f) Tighten the lockscrews [4].
(g) Tignten the locknut [6] 20 in-lb (2 N
m) to 25 in-lb (3 N
m).
(h) Install the lockwire, G01505 on the lockscrews [4], Lockwires Installation,
TASK 20-10-44-400-801.
SUBTASK 27-41-94-820-004
(2) Adjust Type 1 style stabilizer trim limit switch, Figure 501 (Sheet 5):
(a) Remove the lockwire from the lockscrew [4].
(b) Loosen the locknut [6].
(c) Loosen the lockscrew [4].
(d) Using a slot-head screwdriver, turn the lockscrew [4] worm gear until the switch is in the
desired position.
(e) If you can not turn the worm gear with 6 in-lb (0.7 N
m) of torque, then do these steps:
1) Move the stabilizer until the limit switch [1] does not touch the cam.
2) Adjust the limit switch arm [3].
3) Move the stabilizer by hand until the limit switch [1] clicks.
4) Make sure the "B" dimension is the same as follows:
a) With the stabilizer autopilot and electric actuator nose down (flaps not up), make
sure the switch S145 "B" dimension at 0.05 units of trim is 45.48 ±0.05 in.
(1155.2 ±1.3 mm).
GUN 101-122
b) With the stabilizer electric actuator nose down (flaps up), make sure the switch
S844 "B" dimension at 4.30 units of trim is 39.46 ±0.05 in. (1002.3 ±1.3 mm).
GUN 001-099, 155-157, 201-999
c) With the stabilizer electric actuator nose down (flaps up), make sure the switch
S844 "B" dimension at 3.95 units of trim is 39.96 ±0.05 in. (1015.0 ±1.3 mm).
GUN ALL
d) With the stabilizer autopilot and electric actuator nose up, make sure the switch
S144 "B" dimension at 14.50 units of trim is 24.80 ±0.05 in. (629.9 ±1.3 mm).
(f) Tighten the lockscrew [4].
(g) Tignten the locknut [6] 20 in-lb (2 N
m) to 25 in-lb (3 N
m).
(h) Install the lockwire, G01505 on the lockscrews [4], Lockwires Installation,
TASK 20-10-44-400-801.
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-41-94
Page 503
Oct 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
SUBTASK 27-41-94-820-003
(3) Make sure the limit switch arm [3] overtravel is sufficient:
(a) With the stabilizer leading edge in the full down position (airplane nose up), make sure the
switch S144 can be rotated away from the cam surface by a minimum of 0.05 in. (1.27 mm)
with finger pressure only.
(b) With the stabilizer leading edge in the full up position (airplane nose down), make sure the
switches S145 and S844 can be rotated away from the cam surface by a minimum of 0.05 in.
(1.27 mm) with finger pressure only.
SUBTASK 27-41-94-710-002
(4) Do this task: Stabilizer Trim Limit Switches Test, TASK 27-41-94-700-801.
SUBTASK 27-41-94-410-002
(5) Close this access panel:
Number Name/Location
311BL Stabilizer Trim Access Door
------------------------- END OF TASK ---------------------------
737-600/700/800/900
AIRCRAFT MAINTENANCE MANUAL
EFFECTIVITY
GUN ALL 27-41-94
Page 504
Jun 10/2007
D633A101-GUN
BOEING PROPRIETARY - Copyright#Unpublished Work - See title page for details
Stabilizer Trim Limit Switches Adjustment
Figure 501 (Sheet 1 of 5)/27-41-94-990-802
　
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-600-700-800-900 AIRCRAFT MAINTENANCE MANUAL飛機維護(hù)手冊4(24)