-
the anti-collision strobe light (Ref. 33-48-00).
A clear, single piece acrylic/polycarbonate glazing panel is installed on
the wingtip leading edge to give protection to the lights.
A retainer for a static discharger (Ref. 23-60-00) is attached to the wingtip at the trailing edge.
Wing Tip and Wingtip Fence
Figure 001
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-30-00Page 2 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
R Wing Tip and Wingtip Fence
R Figure 001A
R 1EFF : 301-399, 1 57-30-00 Page 3
1 1 May 01/04
1 1
1CES 1
There are two access holes in the wingtip:
- one access hole in the bottom skin, which is closed with the access door 534AB(634AB)
- one access hole in the closing rib adjacent to RIB27, which is closed with a closing plate.
B. Wingtip Fence
The wingtip fence is made of aluminum alloy. It has:
-flanged sheet-metal ribs
-an extruded trailing-edge section
-inboard and outboard etched skins
-a leading edge fairing
-leading edge skin caps and top and bottom end pieces.
The wingtip fence is attached to the outboard edge of the wingtip with bolts. These go through a machined fitting in the fence into a machined rib in the wingtip. Two spigots attached to the wingtip make sure the wingtip fence is in the correct position.
Four retainers for static dischargers (Ref. 23-60-00) are attached to the wingtip fence at the trailing edge.
There are two access holes in the outboard skin of the wingtip fence. These give access to the attachment bolts and are closed with access doors.
WING TIP - INSPECTION/CHECK
___________________________
TASK 57-30-00-200-001
Detailed Visual Inspection of Wing Tip Bottom Skin Lower Surface Joint Outboard of RIB27
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
Refer to the MPD TASK: 573101-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notices
No specific access platform 4 m (13 ft. 1 in.)
98D27803500001 1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-026 GB DEF-STAN 68-148/1 R SOLVENT GENERAL PURPOSE (Ref. 20-31-00) Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
ASRM 573000 (for corrective action) 57-30-00-991-001 Fig. 601
3. Job Set-up
__________
(Ref. Fig. 601/TASK 57-30-00-991-001)
Subtask 57-30-00-941-050
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) on the flap/slat control lever.
(3)
Put warning notices in the cockpit to tell persons not to operate the flaps or slats.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼2(91)
