Subtask 57-21-00-010-083
B. Get Access
(1) Put the adjustable access platform in position at the zone 500(600).
4. Procedure
_________ R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
R (Ref. Fig. 634/TASK 57-21-00-991-040)
Outer Wing, Bottom Skin Lower Surface at Fuel Tank Water Drain Holes between Rib 15-16 and Rib 22-23 R Figure 634/TASK 57-21-00-991-040
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-21-00Page A684 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1R **ON A/C 301-399,
R (Ref. Fig. 634A/TASK 57-21-00-991-040-A)
**ON A/C ALL
Subtask 57-21-00-100-054
A. Preparation for Inspection
(1) Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean the applicable area.
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 57-21-00-210-089
B. General Visual Inspection of Outer Wing, Bottom Skin Lower Surface at Fuel Tank Water Drain Holes, between Rib 15 and Rib 16 and Rib 22-23, and Magnetic Level Indicator Position
(1) Do an inspection and make sure that:
-
there is no damage
-
there are no cracks
-
there is no corrosion
-the paint finish is in the correct condition.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 572100) for the
____
correct repair procedure.
**ON A/C 301-399,
Subtask 57-21-00-210-089-A
B. General Visual Inspection of Outer Wing, Bottom Skin Lower Surface at Fuel Tank Water Drain Holes, and Magnetic Level Indicator Position between Rib 15-16
(1) Do an inspection and make sure that:
-
there is no damage
-
there are no cracks
-
there is no corrosion
-the paint finish is in the correct condition.
Outer Wing, Bottom Skin Lower Surface at Fuel Tank Water Drain Hole between Rib 22-23, and Magnetic Level Indicator between Rib 15-16 R Figure 634A/TASK 57-21-00-991-040-A
R 1EFF : 301-399, 1 57-21-00Page A686 1 1 Aug 01/05 1 1 1CES 1 NOTE : If necessary, refer to the ASRM (Ref. ASRM 572100) for the
____
correct repair procedure.
**ON A/C ALL
5. Close-up
________ Subtask 57-21-00-942-089
A. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Make sure that the work area is clean and clear of tool(s) and other items.
(3)
Remove the warning notice(s).
(4)
Remove the access platform(s).
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
TASK 57-21-00-200-034
Special Detailed Inspection of Attachment Holes for Access in LH/RH Wing Bottom Skin Panel 2, Between Rib 13 and Rib 22 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1.
Reason for the Job
__________________
Refer to the MPD TASK: 572170-01
2.
Job Set-up Information
______________________
Not Applicable
3.
Job Set-up
__________
4.
Procedure
_________
5.
Close-up
________ Subtask 57-21-00-942-090
A. Removal of Equipment
(1)
Remove the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER from the flap/slat control lever.
(2)
Remove the warning notice(s).
(3)
Remove the safety barrriers.
(4)
Remove the access platform(s).
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
TASK 57-21-00-210-006
General Visual Inspection of Outer Wing, Top Skin, Upper Surface at Attachment to Front Spar and Rear Spar, Between RIB8 and RIB22
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼2(7)
