-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.

 -MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
 1. Reason for the Job
__________________
 Refer to the MPD TASK: 572610-01
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
 No specific safety barriers
 No specific warning notice
 No specific access platform 2.5 m (8 ft. 2 in.)

R No specific Torque Wrench : range 0.00 to 1.20 m.daN R (0.00 to 9.00 lbf.ft) 98D27803000000 1 LOCKING TOOL - FLAP/SLAT CONTROL LEVER

 B. Consumable Materials

 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-026 GB DEF-STAN 68-148/1
 SOLVENT GENERAL PURPOSE (Ref. 20-31-00)
 Material No. 19-003 USA AMS 3819
 LINT-FREE COTTON CLOTH (Ref. 20-31-00)

 C. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-866-008 Extension of the Flaps on the Ground 27-50-00-866-009 Retraction of the Flaps on the Ground 57-55-11-000-001 Removal of the Flap Track Fairings Nos. 2, 3 and 4 57-55-11-000-004 Removal of the Flap Track Fairings Nos. 2, 3 and 4 57-55-11-400-001 Installation of the Flap Track Fairings Nos. 2, 3 and
 4 57-55-11-400-004 Installation of the Flap Track Fairings Nos. 2, 3 and 4 ASRM 572600 (for corrective action) R CMM 57-51-41 (for corrective action) 57-26-00-991-011 Fig. 611
 3. Job Set-up
__________
 Subtask 57-26-00-941-066
 A. Safety Precautions
 (1)
 Put the safety barriers in position.

 (2)
 Put warning notice in the cockpit to tell persons not to operate the flaps or slats.

 Subtask 57-26-00-866-062

 B. Aircraft Maintenance Configuration
 (1)
 Fully extend the flaps (Ref. TASK 27-50-00-866-008).

 (2)
 Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER is on the control lever.

 Subtask 57-26-00-865-062
 C. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21

R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
 Subtask 57-26-00-010-067
 D. Get Access
 (1)
 Put the access platform below the applicable wing trailing edge at the flap tracks 2, 3 and 4, zones 531(631), 532(632) and 533(633).

 (2)
 Remove the applicable flap track fairing access panels (Ref. TASK 57-55-11-000-001):

 (a)
 For the flap track 2,:

 -
for the left wing, remove 531CB

 -
for the right wing, remove 631CB.

 (b)
 For the flap track 3,:

 -
for the left wing, remove 532CB

 -
for the right wing, remove 632CB.

 (c)
 For the flap track 4,:

 -
for the left wing, remove 533CB

 -
for the right wing, remove 633CB.

 **ON A/C 301-399,

 Subtask 57-26-00-010-067-A
 D. Get Access
 (1)
 Put the access platform below the applicable wing trailing edge at the flap tracks 2, 3 and 4, zones 531(631), 532(632) and 533(633).

 (2)
 Remove the applicable flap track fairing access panels (Ref. TASK 57-55-11-000-004):

 (a)
 For the flap track 2,:

 -
for the left wing, remove 531CB

 -
for the right wing, remove 631CB.

 (b)
 For the flap track 3,:

 -
for the left wing, remove 532CB

 -
for the right wing, remove 632CB.

 (c)
 For the flap track 4,:

 -
for the left wing, remove 533CB

 -
for the right wing, remove 633CB.

 
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼2(33)