-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific safety barriers No specific warning notice No specific access platform 3 m (9 ft. 10 in.) 98D27803500001 1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
57-41-37-000-004 Removal of the Pressure-Relief Panels 521AB(621AB), 521CB(621CB), 521EB(621EB), 522AB(622AB), 522CB(622CB)
57-41-37-991-022 Fig. 402
1EFF : ALL 1 57-41-37Page 424 1 1 Aug 01/04R 1 1 1CES 1
3. Job Set-up
__________ Subtask 57-41-37-941-065
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Install the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER (98D27803500001) on the flap/slat control lever.
(3)
Put a warning notice in the cockpit to tell persons not to operate the slats.
Subtask 57-41-37-865-076
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1 5CV B06 121VU FLIGHT CONTROLS/SLT/CTL/SYS2 7CV R21
4. Procedure
_________ (Ref. Fig. 402/TASK 57-41-37-991-022) Subtask 57-41-37-010-063
A. Get Access
(1)
Put the access platform in position below the applicable NACA duct panel 521BB(621BB).
(2)
Remove the pressure-relief panels 521AB(621AB) and 521CB(621CB) adjacent to the NACA duct panel (1) (Ref. TASK 57-41-37-000-004).
Subtask 57-41-37-020-057
B. Removal of the NACA Duct Panel 521BB(621BB) NOTE : Some of the screws that hold the NACA duct panel (1) in position
____ are longer than the others. Make a record of the position of each screw as it is removed.
1EFF : ALL 1 57-41-37Page 425 1 1 Aug 01/04R 1 1 1CES 1
NACA Duct Panel 521BB(621BB) - Location and Detail Figure 402/TASK 57-41-37-991-022
1EFF : 1 1R 1CES ALL 1 11 1 57-41-37 Page 426 Aug 01/04
(1)
Hold the panel (1). Remove the three screws (2) and the four screws (3).
(2)
Carefully remove the panel (1).
(3)
Remove the packer (4).
1EFF : ALL 1 57-41-37Page 427 1 1 Aug 01/04R 1 1 1CES 1
TASK 57-41-37-400-005
Installation of the NACA Duct Panel 521BB(621BB)
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific access platform No specific safety barriers No specific warning notice
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
57-41-37-000-004 Removal of the Pressure-Relief Panels 521AB(621AB), 521CB(621CB), 521EB(621EB), 522AB(622AB), 522CB(622CB)
57-41-37-400-002 Installation of the Pressure-Relief Panels 521AB(621AB), 521CB(621CB), 521EB(621EB), 522AB(622AB), 522CB(622CB)
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼2(137)
