Outer Wing Pylon - Aft Attachment fitting Lug - Inspection
Figure 605/TASK 57-26-00-991-005
1EFF : ALL 1 57-26-00Page 625 1 1 Feb 01/05R 1 1 1CES 1
R R (4) If the top bearing sealant shows signs of cracks, replace the sealant (Ref. TASK 57-26-12-000-001) and (Ref. TASK 57-26-12-400-001).
R R NOTE : It is not necessary to remove the shackles or the engine to do____ these procedures.
R R (5) Examine the forward and aft attachment bolts. Make sure that the bolts show no signs of movement.
R (6) If the bolts show signs of movement:
R R (a) Make a visual inspection of the lockwasher and the slotted nut for damage.
R R R R R R R (b) If damage to the lockwasher or the slotted nut is found, then these items should be replaced: - for the forward attachment bolts (Ref. TASK 54-51-17-000-001) and (Ref. TASK 54-51-17-400-001) - for the aft attachment bolts (Ref. TASK 54-51-17-000-002) and (Ref. TASK 54-51-17-400-002).
5. Close-up________
Subtask 57-26-00-410-055
A. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Install the pylon access panels: - for the LH pylon, install 471CL, 475BL, 472BR, 476BR - for the RH pylon, install 481BL, 485BL, 482CR, 486BR.
Subtask 57-26-00-942-055
B. Removal of Equipment
(1) Remove the warning notice(s).
(2) Remove the access platform(s).
(3) Remove the ground support and maintenance equipment, the special and standard tools and all other items.
TASK 57-26-00-200-004
Detailed Inspection of Outer Wing, Flap Track Beams 2, 3, 4 Track Upper Flange Radii
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Refer to the MPD TASK: 572601-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific safety barriers No specific warning notices No specific access platform 2.5 m (8 ft. 2 in.) 98D27803000000 1 LOCKING TOOL - FLAP/SLAT CONTROL LEVER 98D27803500001 1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER
1EFF : ALL 1 57-26-00Page 627 1 1 Feb 01/05R 1 1 1CES 1
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-026 GB DEF-STAN 68-148/1
SOLVENT GENERAL PURPOSE (Ref. 20-31-00) Material No. 19-003 USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-866-008 Extension of the Flaps on the Ground 27-50-00-866-009 Retraction of the Flaps on the Ground 57-55-11-000-001 Removal of the Flap Track Fairings Nos. 2, 3 and 4 57-55-11-000-004 Removal of the Flap Track Fairings Nos. 2, 3 and 4 57-55-11-400-001 Installation of the Flap Track Fairings Nos. 2, 3 and
4 57-55-11-400-004 Installation of the Flap Track Fairings Nos. 2, 3 and
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼2(22)
