4. Procedure
_________
(Ref. Fig. 602/TASK 57-41-00-991-002)
Subtask 57-41-00-110-055
A. Preparation for Inspection
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(1) Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-004) to clean the parts of the roller contact-areas of slat tracks 9 and 10 that you can see.
Subtask 57-41-00-210-059
B. Inspection
(1) Examine the parts of the roller contact-areas of the slat-tracks 9 and 10 that you can see. Make sure that:
-
there is no damage
-
there is no distortion
-
there is no corrosion
-the protective surface is in the correct condition
-there are no scores.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 574000) for the
____
correct repair procedure.
5. Close-up
________
Subtask 57-41-00-865-081
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 5CV, 7CV.
1EFF : ALL 1 57-41-00Page 639 1 1 May 01/04R 1 1 1CES 1
Subtask 57-41-00-860-055
B. Aircraft Configuration
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the access platform(s).
(3) Fully retract the slats (Ref. TASK 27-80-00-866-005). Subtask 57-41-00-942-071
C. Removal of Equipment
(1)
Remove the warning notice(s).
(2)
Remove the safety barriers.
1EFF : ALL 1 57-41-00Page 640 1 1 May 01/04R 1 1 1CES 1
TASK 57-41-00-200-011
Detailed Visual Inspection of Slat 5, Tracks 11 and 12: Visible Part of Roller Contact Area
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
1. Reason for the Job
__________________
Refer to the MPD TASK: 574601-01
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notices
No specific adjustable access platform 3.0 m (9 ft. 10 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-004 USA MIL-T-81533 1.1.1TRICHLOROETHANE (METHYL CHLOROFORM) (Ref. 20-31-00)
Material No. 19-003 USA AMS 3819 LINT-FREE COTTON CLOTH (Ref. 20-31-00)
1EFF : ALL 1 57-41-00Page 641 1 1 May 01/04R 1 1 1CES 1
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-80-00-866-004 Extending the Slats on the Ground 27-80-00-866-005 Retracting the Slats on the Ground ASRM 574000 (for corrective action) 57-41-00-991-002 Fig. 602
3. Job Set-up
__________ Subtask 57-41-00-941-067
A. Safety Precautions
(1) Put warning notices in the cockpit to tell persons not to operate the flaps or slats.
(2) Put the safety barriers in position. Subtask 57-41-00-860-056
B. Aircraft Maintenance Configuration
(1)
Fully extend the slats (Ref. TASK 27-80-00-866-004).
(2)
Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER is installed on the flap/slat control lever.
(3)
Put the adjustable access platform in position below the applicable slat-track(s), zone 522(622).
Subtask 57-41-00-865-082
中國航空網(wǎng) m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM WINGS 機(jī)翼2(117)
