-
for the rollers at slat tracks 5 and/or 6, remove the slat No. 2 (Ref. TASK 27-84-64-000-001)
-
for the rollers at slat tracks 7 and/or 8, remove the slat No. 3 (Ref. TASK 27-84-65-000-001)
-
for the rollers at slat tracks 9 and/or 10, remove the slat No. 4 (Ref. TASK 27-84-66-000-001)
-
for the rollers at slat tracks 11 and/or 12, remove the slat No. 5 (Ref. TASK 27-84-67-000-001).
(3)
Remove the applicable slat tracks:
-
for slat tracks 1 thru 4 (Ref. TASK 27-84-61-000-001)
-
for slat tracks 5 thru 12 (Ref. TASK 27-84-62-000-001).
Subtask 57-41-33-865-050
C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1 5CV B06 121VU FLIGHT CONTROLS/SLT/CTL/SYS2 7CV R21
4. Procedure
_________ Subtask 57-41-33-020-051
A. Removal of the Slat-Track Vertical-Load Rollers
(1)
Removal of the bottom vertical-load rollers at tracks 1, 2, 5 and 8 (Ref. Fig. 401/TASK 57-41-33-991-001)
(a)
Remove and discard the applicable cotter pins (126) thru (133).
(b)
Remove the nut (134) and the washer (125).
(c)
Remove the pin (124) and the roller (135).
(d)
If necessary, remove the greaser (123) from the pin (124)
(2)
Removal of the top vertical-load rollers at tracks 1, 2, 5 and 8 (Ref. Fig. 401/TASK 57-41-33-991-001)
(a)
Remove and discard the applicable cotter pins (139) thru (146).
(b)
Remove the nut (138), the pin (137) and the roller (147). NOTE : Do not remove the eccentric bush.
____
(c)
If necessary, remove the greaser (136) from the pin (137).
(3)
Removal of the bottom vertical-load rollers at tracks 3, 4, 6, 7, 9, 10, 11 and 12 (Ref. Fig. 402/TASK 57-41-33-991-002)
(a)
Remove and discard the applicable cotter pins (75) thru (90).
(b)
Remove the nut (74) and the washer (91).
Vertical Load Rollers at Tracks 1, 2, 5 and 8
Figure 401/TASK 57-41-33-991-001
1EFF : ALL 1 57-41-33 Page 404
1 1 Feb 01/98
1 1
1CES 1
Vertical Load Rollers at Tracks 3, 4, 6, 7, 9, 10, 11 and 12
Figure 402/TASK 57-41-33-991-002
(c)
Remove the pin (92) and the roller (94).
(d)
If necessary, remove the greaser (93) from the pin (92).
(4) Removal of the top vertical-load rollers at tracks 3, 4, 6, 7, 9, 10, 11 and 12 (Ref. Fig. 402/TASK 57-41-33-991-002)
(a)
Remove and discard the applicable cotter pins (96) thru (110).
(b)
Remove the nut (95).
(c)
Remove the pin (111) and the roller (113).
NOTE : Do not remove the eccentric bush.
____
(d)
If necessary, remove the greaser (112) from the pin (111).
TASK 57-41-33-400-001
Installation of the Slat-Track Vertical-Load Rollers
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific lint-free cloth or tissue
No specific warning notices
No specific adjustable access platform 4 m (13 ft. 1 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼2(127)
