_______
 GEAR.

 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
 START A TASK ON OR NEAR:

 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific adjustable access platform
 No specific circuit breaker(s) safety clip(s)
 No specific safety barriers
 No specific warning notice
 98D27803500001 1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER

 3. Job Set-up
__________
 Subtask 57-41-37-941-062

 A. Safety Precautions
 (1) Put the safety barriers in position.
R (2) Make sure that the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER
R (98D27803500001) is installed on the flap/slat control lever.

R  (3) Put a warning notice in the cockpit to tell persons not to operate 
R  the slats. 
R  (4) Put the adjustable access platform in position below the applicable 
R  pressure-relief panel to be removed. 
R  Subtask 57-41-37-865-072 
R  B. Open, safety and tag this(these) circuit breaker(s): 
R  -------------------------------------------------------------------------------
R  PANEL DESIGNATION IDENT. LOCATION 
R  -------------------------------------------------------------------------------
R  49VU FLIGHT CONTROLS/SLT/CTL AND MONG/SYS1 5CV B06 
R  121VU FLIGHT CONTROLS/SLT/CTL/SYS2 7CV R21 
R  4. Procedure_________ 
R  Subtask 57-41-37-020-052 
R  A. Removal of the Pressure-Relief Panels 521AB(621AB), 521CB(621CB), 
R  521EB(621EB), 522AB(622AB), 522CB(622CB) 
R  NOTE : On many of the pressure-relief panels, the screws that retain the____ 
R  panel have different lengths. Make a record of the position of 
R  each screw as it is removed. 
R  (1) For the panel 521AB(621AB): 
R  (a) Hold the panel (1) and remove the screws (2). 
R  (b) Carefully remove the panel (1). 
R  (2) For the panel 521CB(621CB): 
R  (a) Hold the panel (3) and remove the screws (4). 
R  (b) Carefully remove the panel (3). 
R  (3) For the panel 521EB(621EB): 
R  (a) Hold the panel (5). Remove the four screws (6) and the screws 
R  (7). 
R  (b) Carefully remove the panel (5).

R  (4) For the panel 522AB(622AB): 
R  (a) Hold the panel (8). Remove the four screws (9) and the screws 
R  (10). 
R  (b) Carefully remove the panel (8). 
R  (5) For the panel 522CB(622CB): 
R  (a) Hold the panel (11). Remove the screw (12) and the screws (13). 
R  (b) Carefully remove the panel (11).

 TASK 57-41-37-400-002
 Installation of the Pressure-Relief Panels 521AB(621AB), 521CB(621CB),
 521EB(621EB), 522AB(622AB), 522CB(622CB)

 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
 GEAR.

 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
 START A TASK ON OR NEAR:

 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific adjustable access platform
 No specific non-metallic scraper
 No specific safety barriers
 No specific warning notice

R No specific Torque Wrench : range 0.00 to 1.20 m.daN
　
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM WINGS 機翼2(131)