R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 27-54-62Page 434 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1

 **ON A/C 301-399,

 TASK 27-54-62-000-002
 Removal of the Outboard Double-Slotted Flap
 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS

 -COMPONENTS THAT MOVE.
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
 CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.

 -
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.

 -MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific adhesive tape No specific covers No specific pneumatic wrench No specific safety barriers No specific support structure No specific warning notice No specific access platform 3 m (9 ft. 10 in.) 98D27504083000 1 EXTRACTOR - PIN TRACKS 2 AND 3 98D27504084000 1 EXTRACTOR - PIN 98D27504115000 1 DISTANCE GAUGES 98D27604000000 4 COLLAR-SAFETY, SPOILER 98D27804001000 1 ADAPTOR-DRIVE, SLAT (AND FLAP)
 1EFF : 301-399, 1 27-54-62Page 435 1 1 May 01/05R 1 1 1CES 1

 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-000-002
27-50-00-400-002
27-50-00-866-009 27-51-00-820-004
27-54-41-000-001 27-54-61-000-002 27-60-00-866-002 57-55-11-010-002
27-54-62-991-021 27-54-62-991-022 27-54-62-991-023 27-54-62-991-038 27-54-62-991-039 27-54-62-991-040 27-54-62-991-024 27-54-62-991-025 27-54-62-991-030
3. Job Set-up
__________
 Subtask 27-54-62-941-056
 A. Safety PrecautionsRemoval of the Inboard and Outboard Flap Hoisting-SlingInstallation of the Inboard and Outboard Flap Hoisting-SlingRetraction of the Flaps on the GroundAdjustment of the Forward Eccentrics to the Datum PositionRemoval of the Right Angle Gearbox 6203CM,(6253CM)Removal of the Flap Kink-SealsExtension-Retraction of the Spoilers for MaintenanceTo Lower the Flap Track No. 3 & No. 4 Movable Fairings for AccessFig. 409Fig. 410Fig. 411Fig. 412Fig. 413Fig. 414Fig. 415Fig. 416Fig. 417
 (1)
 Put the safety barriers in position.

 (2)
 Put a warning notice on panel 400VU to tell persons not to operate the landing gear.

 (3)
 Put a warning notice on panel 114VU to tell persons not to operate the flight controls.

 1EFF : 301-399, 1 27-54-62Page 436 1 1 May 01/05R 1 1 1CES 1

 Subtask 27-54-62-860-056
 B. Aircraft Maintenance Configuration
 WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
 (1)
 Make sure that the flaps are in the fully retracted position (Ref. TASK 27-50-00-866-009).

 (2)
 Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER (98D27803000000) is on the slat/flap control lever.

 Subtask 27-54-62-865-054
 C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
 Subtask 27-54-62-010-052
 D. Get Access
 (1)
 Put the access platform in position below the applicable outboard flap.

 (2)
 Remove the access panels for the applicable wing:
 (Ref. Fig. 409/TASK 27-54-62-991-021)

 -
for the left wing, remove 573CB, 575AB, 575BB

 -
for the right wing, remove 673CB, 675AB, 675BB.