Spoiler 5 - Hinge Detail Figure 402/TASK 27-64-45-991-002- 22 (SHEET 2)
R 1EFF : 001-003, 051-052, 1 27-64-45Page 411 1 1 May 01/05 1 1 1CES 1
Spoiler 5 - Hinge Detail
Figure 402A/TASK 27-64-45-991-002-A
R 1EFF : 004-049, 053-099, 101-149, 151-199, 1 27-64-45Page 412 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(e)
Remove the STA-LOK nuts (26) and (46) with the WRENCHES -NOTCHED, TIGHTENING OF NUTS NSA5454 (SL90-315-5000).
(f)
Remove the STA-LOK nuts (32) and (34) with the WRENCHES -NOTCHED, TIGHTENING OF NUTS NSA5454 (SL90-315-6250).
(5)
Do not remove the hinge pins (24), (30), (38) and (47).
(6)
Prepare the spoiler 5 for removal: CAUTION : SUPPORT THE SERVO CONTROL 7.5kg (16.5lb) AND THE SPOILER
_______ APPROXIMATELY 15kg (33lb). THIS WILL PREVENT DAMAGE TO:
-
THE HYDRAULIC LINES
-
THE ELECTRICAL CABLES
-
THE STRUCTURE.
(a) Put the spoiler 5 and the actuator on supports. Remove the hinge pin (4) from the actuator eye-end (6). Carefully lower the spoiler and remove the sliding bush (3) and the flanged bush (5).
(7) Continue to hold the spoiler, remove the hinge pins (24), (30), (38) and (47) and collect the sliding bushes (25), (31), (36) and (37).
(8)
Remove the spoiler from the wing. If the spoiler is safetied with ABS 0738 nuts, do the steps that follow:
(9) Remove the nuts (49), the washers (50) and the bolts (41) to disconnect the bonding straps (48) from each end of the spoiler 5.
(10)
Remove the nuts (21), (30) and (46) and the locking plates (22), (31) and (45).
(11)
Remove the spacer (20) and the bolt (29).
(12)
Remove the items that follow:
(a)
Remove and discard the cotter pin (1) from the locking cap (2).
(b)
Remove the locking cap (2), the nut (3) and the washer (4). Do not remove the hinge pin (6).
(c)
Remove and discard the cotter pins (28) and (51) from the locking caps (27) and (52).
(d)
Remove and discard the cotter pins (37) and (38) from the locking caps (36) and (39).
R 1EFF : 001-003, 051-052, 1 27-64-45Page 413 1 1 May 01/05 1 1 1CES 1
(e)
Remove the locking caps (27), (52), (36) and (39).
(f)
Remove the nuts (26), (53), (35) and (40).
(g)
Remove the washers (25), (54), (34) and (41).
(13)
Do not remove the hinge pins (23), (32), (44) and (55).
(14)
Prepare the spoiler 5 for removal: CAUTION : SUPPORT THE SERVO CONTROL 7.5kg (16.5lb) AND THE SPOILER
_______ APPROXIMATELY 15kg (33lb). THIS WILL PREVENT DAMAGE TO:
-
THE HYDRAULIC LINES
-
THE ELECTRICAL CABLES
-
THE STRUCTURE.
(a) Put the spoiler 5 and the actuator on supports. Remove the hinge pin (6) from the actuator eye-end (8). Carefully lower the spoiler and remove the sliding bush (5) and the flanged bush (7).
(15) Continue to hold the spoiler, remove the hinge pins (23), (32), (44) and (55) and collect the sliding bushes (24), (33), (42) and (43).
(16) Remove the spoiler from the wing. R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 27-64-45-020-050-A
A. Removal of the Spoiler 5
(1)
Remove the nuts (49), the washers (50) and the bolts (47) to disconnect the bonding straps (48) from each end of the spoiler 5.
(2)
Remove the nuts (21), (30) and (46) and the locking plates (22), (31) and (45).
(3)
Remove the spacer (20) and the bolt (29).
(4)
Remove the items that follow:
(a)
Remove and discard the cotter pin (1) from the locking cap (2).
(b)
Remove the locking cap (2), the nut (3) and the washer (4). Do not remove the hinge pin (6).
(c)
Remove and discard the cotter pins (28) and (51) from the locking caps (27) and (52).
(d)
Remove and discard the cotter pins (37) and (38) from the locking caps (36) and (39).
(e)
Remove the locking caps (27), (52), (36) and (39).
(f)
Remove the nuts (26), (53), (35) and (40).
(g)
Remove the washers (25), (54), (34) and (41).
(5)
Do not remove the hinge pins (23), (32), (44) and (55).
(6)
Prepare the spoiler 5 for removal: CAUTION : SUPPORT THE SERVO CONTROL 7.5kg (16.5lb) AND THE SPOILER
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱6(178)
