Subtask 27-54-61-860-063
B. Aircraft Maintenance Configuration
(1)
Make sure that the flaps are fully extended (Ref. TASK 27-50-00-866-008).
(2)
Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER is installed on the slat/flap control lever.
(3)
Make sure that the access platform is below the applicable inboard flap, zone 581(681).
1EFF : ALL 1 27-54-61Page 475 1 1 Aug 01/05R 1 1 1CES 1
4. Procedure
_________ (Ref. Fig. 412/TASK 27-54-61-991-050) CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
_______
EDGE:
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
Subtask 27-54-61-420-088
A. Preparation for Installation
(1)
Clean the component interface and/or the adjacent area with a clean MISCELLANEOUS (Material No. 19-003) made moist with CLEANING AGENTS (Material No. 11-026).
(2)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(3) Do an inspection of the component interface and/or the adjacent area. Subtask 27-54-61-420-089
B. Installation of the Inboard Flap Seals
(1) Install the flap seals as follows:
(a)
Position the seal assemblies (2) and (5) on the inboard end of the flap.
(b)
Install the screws (1).
(c)
Install the cover strip (4) and the screws (3).
(d)
TORQUE the screws (1) and (3) to between 0.4 and 0.45 m.daN
(35.39 and 39.82 lbf.in).
(e) Check and, if necessary, adjust the flap seals for the correct flap seal to belly-fairing dimensions (Ref. TASK 27-54-61-400-001).
1EFF : ALL 1 27-54-61Page 476 1 1 Aug 01/05R 1 1 1CES 1
5. Close-up
________ Subtask 27-54-61-865-059
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
Subtask 27-54-61-860-064
B. Aircraft Maintenance Configuration
(1) Fully retract the flaps (Ref. TASK 27-50-00-866-009). Subtask 27-54-61-942-060
C. Removal of Equipment
(1)
Remove the access platform(s).
(2)
Remove the warning notice(s).
(3)
Remove the safety barriers.
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
R 1EFF : ALL 1 27-54-61Page 477 1 1 Aug 01/05 1 1 1CES 1 **ON A/C 301-399,
TASK 27-54-61-000-004
Removal of the Inboard Flap Tab
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers No specific support structure No specific warning notice No specific access platform 3 m (9 ft. 10 in.) 98D27504114000 2 DISTANCE GAUGES
1EFF : 301-399, 1 27-54-61Page 478 1 1 Aug 01/05R 1 1 1CES 1
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-866-009 Retraction of the Flaps on the Ground 27-54-41-000-001 Removal of the Right Angle Gearbox 6203CM,(6253CM) 27-54-61-000-003 Removal of the Inboard Double-Slotted Flap 57-55-11-000-005 Removal of the Inboard and Outboard Flap Tab
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱6(35)
