(b)
TORQUE the nut (47) to between 2.2 and 2.4 m.daN (16.22 and 17.69 lbf.ft).
(c)
Safety the nut (47) with the new cotter pin (46).
(2)
If necessary, adjust the tab drive control-mechanism (Ref. TASK 27-54-61-400-003).
(3)
At the track 2 flap carriage, connect and if necessary, adjust the tab drive control-rod (73) (Ref. TASK 27-54-61-400-003). (Ref. Fig. 415/TASK 27-54-61-991-029)
(4)
Remove the DISTANCE GAUGES from the hinge 1A and the track 2 positions.
(5)
Install the ADAPTOR-DRIVE, SLAT (AND FLAP) (98D27804001000) on the right angle gearbox.
1EFF : 301-399, 1 27-54-61Page 495 1 1 Aug 01/05R 1 1 1CES 1
(6)
Use a pneumatic wrench to turn the ADAPTOR-DRIVE, SLAT (AND FLAP) to fully extend and retract the flaps. Make sure that the tab operates correctly.
(7)
Remove the ADAPTOR-DRIVE, SLAT (AND FLAP) from the right angle gearbox.
(8)
Remove the LOCK-TORQUE SHAFT (FLAPS AND SLATS) WITH CLAMP-PIVOT (98D27504030001).
(9) Connect the right angle gearbox (Ref. TASK 27-54-41-400-001). Subtask 27-54-61-410-054
D. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the fairings at the hinge 1A and the hinge 1B positions (Ref. TASK 57-55-11-400-005).
(3)
Lift the flap track No. 2 movable fairing (Ref. TASK 57-55-11-410-001).
Subtask 27-54-61-865-056
E. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
Subtask 27-54-61-710-052
F. Test CAUTION : DO NOT MOVE THE FLAP OR TAB WITH THE DISTANCE GAUGE INSTALLED
_______
OR YOU WILL CAUSE DAMAGE TO THE FLAP.
(1)
Before you do the test make sure that the DISTANCE GAUGES are removed.
(2)
Do an operational test of the flap system (Ref. TASK 27-54-00-710-001).
1EFF : 301-399, 1 27-54-61Page 496 1 1 Aug 01/05R 1 1 1CES 1
5. Close-up
________ Subtask 27-54-61-942-057
A. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Remove the warning notice(s).
(3)
Remove the access platform(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : 301-399, 1 27-54-61Page 497 1 1 Aug 01/05R 1 1 1CES 1
TASK 27-54-61-000-003
Removal of the Inboard Double-Slotted Flap
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific adhesive tape No specific blanking caps No specific covers No specific pneumatic wrench No specific safety barriers No specific support structure No specific warning notice No specific access platform 3 m (9 ft. 10 in.) 98D27504083000 1 EXTRACTOR - PIN TRACKS 2 AND 3 98D27504114000 2 DISTANCE GAUGES 98D27604000000 1 COLLAR-SAFETY, SPOILER 98D27804001000 1 ADAPTOR-DRIVE, SLAT (AND FLAP)
1EFF : 301-399, 1 27-54-61Page 498 1 1 Aug 01/05R 1 1 1CES 1
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-000-002
27-50-00-400-002
27-50-00-866-008 27-50-00-866-009 27-51-44-000-001 27-54-41-000-001 27-54-61-000-002 27-60-00-866-002 54-55-00-000-001 57-51-37-000-002
57-51-37-000-004
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱6(41)
