3.0 mm (0.1181 in.). Adjust the seal if it is necessary.
(2)
Make sure that the clearance 'V' is between 0 mm (0.0 in.) and 0.5 mm (0.0196 in.). Adjust the seals if it is necessary.
(3)
Make sure that the clearance 'Y' is between 5.5 mm (0.2165 in.) and
7.5 mm (0.2952 in.).
(4)
Make sure that the clearance 'W' is between 16.0 mm (0.6299 in.) and
20.0 mm (0.7874 in.).
(5)
Make sure that the clearance 'Z' is between 1.63 mm (0.0641 in.) and
2.82 mm (0.1110 in.) and that the spoiler and the structure make a continuous surface. The seal must touch the trailing edge along its full length.
(6)
Pressurize the Yellow Hydraulic system (Ref. TASK 29-10-00-863-002).
(7)
Adjust the spoiler to give the dimension 'U' between the spoiler and the flap (Ref. TASK 27-64-00-820-001).
Subtask 27-64-42-410-052
J. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the access panel 575BB, 675BB (Ref. TASK 57-51-37-400-004):
(3) Remove the access platform(s). Subtask 27-64-42-865-054
K. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV, 21CE1, 21CE2, 21CE3.
R 1EFF : ALL 1 27-64-42Page 430 1 1 May 01/05 1 1 1CES 1 Subtask 27-64-42-710-050
L. Operational Test
(1) Do an operational test of the spoiler (Ref. TASK 27-64-00-710-001).
5. Close-up
________ Subtask 27-64-42-942-051
A. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Remove the warning notice(s).
(3)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 27-64-42Page 431 1 1 May 01/05R 1 1 1CES 1
SPOILER 2 - INSPECTION/CHECK
____________________________ TASK 27-64-42-200-001 Inspection/Check of the Spoiler 2 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1.
Reason for the Job
__________________
Inspection/check of the spoiler 2 after too much free movement is found.
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers No specific warning notice
1EFF : ALL 1 27-64-42Page 601 1 1 Feb 01/03R 1 1 1CES 1
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
27-64-42-000-001 Removal of the Spoiler 2
27-64-42-400-001 Installation of the Spoiler 2
**ON A/C 001-003, 051-052,
27-64-42-991-003 Fig. 601 R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 401-499,
27-64-42-991-003-A Fig. 601A
**ON A/C 301-399,
27-64-42-991-003-B Fig. 601B
**ON A/C ALL
3. Job Set-up
__________
Subtask 27-64-42-941-053
A. Safety Precautions
(1)
Put the safety barriers in position.
(2)
Put a warning notice in position to tell persons not to operate the flight controls.
Subtask 27-64-42-010-051
B. Get Access
(1) Remove the spoiler 2 (Ref. TASK 27-64-42-000-001).
4. Procedure
_________
**ON A/C 001-003, 051-052,
(Ref. Fig. 601/TASK 27-64-42-991-003) R **ON A/C 004-049, 053-099, 101-149, 151-199, 201-299, 401-499,
(Ref. Fig. 601A/TASK 27-64-42-991-003-A)
**ON A/C 301-399,
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM FLIGHT CONTROLS 飛行操縱6(145)
