(2)
Apply SPECIAL MATERIALS (Material No. 05-013) along the mating surfaces at the elevator.
Subtask 55-22-11-410-051
B. Visual Inspection
(1) Make sure that the work area is clean and clear of tool(s) and other items.
Subtask 55-22-11-420-050
C. Install Access Panels
(1) Put the leading-edge access panels (1), (2), (3) and (4) in position.
(2) Install the screws (5). Subtask 55-22-11-110-051
D. Cleaning
(1) Clean the gaps around the leading-edge access panels with CLEANING AGENTS (Material No. 11-008).
Subtask 55-22-11-914-051
E. Sealing
(1) Apply SEALANTS (Material No. 09-005) to the gap along the mating surfaces of the leading-edge access panels (1), (2), (3) and (4).
5. Close-up
________ Subtask 55-22-11-410-050
A. Close Access
(1) If removed, install THS trailing edge access panels (Ref. TASK 55-13-11-400-001)
Subtask 55-22-11-942-051
B. Remove Ground Equipment
(1) Remove the ground support and maintenance equipment, the special and standard tools and all other items. Remove the access platform(s). Remove the warning notice(s).
Subtask 55-22-11-081-050
C. Remove Locking Devices
R R (1) Remove the SETTING TOOL-NEUTRAL, ELEVATOR from the CAPT and F/O side stick controllers.
R R (2) Remove the SAFETY COLLAR-SERVOCONTROL, ELEVATOR from the servocontrol elevator.
Subtask 55-22-11-865-051
D. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 15CE1, 15CE2, 16CE1, 16CE2, 19CE1, 19CE2, 19CE3, 21CE1, 21CE2, 21CE3, 22CE
ELEVATOR TIPS AND INBOARD END CAPS - DESCRIPTION AND OPERATION
______________________________________________________________
1. General.________
A. Each elevator has a tip and an inboard end cap. The tips are installed on the outboard ends of the elevators. The inboard end caps are installed on the inboard ends of the elevators. You can remove the tips and the inboard end caps.
2. Description.____________ (Ref. Fig. 001)
A. Inboard End Caps.
-The inboard end caps are made from laminations of Carbon Fiber Reinforced Plastic (CFRP) on a honeycomb core. They are attached to the elevator ribs 1. Countersunk screws attach them. Tips, which are made of light alloy, make the trailing edges of the end caps stronger. They are riveted to the end caps.
B. Tips.
-The elevator tips are made of light alloy. Ribs of the same material make them stronger. Countersunk screws attach the tips. Each tip has two static dischargers.
Elevator Tips and Inboard End Caps
Figure 001
1EFF : ALL 1 55-24-00 Page 2
1 1 Feb 01/98
1 1
1CES 1
TIPS AND END/CAPS - ELEVATOR - REMOVAL/INSTALLATION
___________________________________________________ TASK 55-24-11-000-001 Removal of the Elevator Tips and Inboard End Caps. WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE CLEAR.
_______
MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR
DAMAGE.
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROL SURFACES ARE
_______
CLEAR BEFORE YOU PRESSURIZE/DEPRESSURIZE A HYDRAULIC SYSTEM.
WARNING : WEAR AND ATTACH A SAFETY HARNESS WHEN YOU WORK ON HIGH SECTIONS. A
_______
FALL CAN INJURE OR KILL YOU.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
CAUTION : DO NOT CAUSE DAMAGE TO THE SURFACES. THE COMPONENTS ARE MADE OF
_______
CARBONFIBER REINFORCED PLASTIC.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
中國航空網 m.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM STABILIZERS 安定面(64)
